780165
6
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
6
ERASING TEMPORARY DATA
To erase the temporary data (trip, time, avg, max)
twice push the button M. rES will show on the
display. Pick option M with buttons A and C
and confirm with buttonM.
PARAMETERS SETTING
To enter the mode of parameter setting press
twice the M button. To change a parameter,
use buttons A andC and for saving the set
parameter press the M button.
TURNING ON THE LIGHTING
IF IT IS INSTALLED
Turning on the front and rear light is done by
pushing and holding the A button for 1 second.
USB PORT
The display is equipped with a micro USB port
for charging of mobile devices (5V/0,5W).
To connect your device with the charging
connector, use any adapter or cable with Micro
USBB connector.
WALKING ASSISTANT
Walking assistant can be activated by pressing
and holding the Cbutton on the control display.
For activation of the assistant assistance mode
must be set to 1-5. This function serves to enable
easier manipulation with e-bike, usually when
walking the bike by your side. The e-bike speed
will be between 4 and 6 km/h. Walking assistant
will be turned off immediately after letting go of
the button.
WARNING: Do not block the e-bike
Lafter the activation of the walking
assistant. The motor can get damaged
that way.
SPEED AND DISTANCE INDICATOR MODE
CHANGE
Change of information displayed on the display
can be done by short press of the button M.
Information shows in this order:
rES – reset of daily kilometres
Un – unit setting (km / mile)
Ld – setting of the bike circumference in cm (max. +/- 5 % from the default setting of the circumference)
bL – display backlight setting in 1-3 range
Ls – speed limit; value 20 means max. assisted speed of 25 km/h
SPS – wheel speed sensor signal
Cr – value of the electric current
TRIP
Lenght of the trip
ODO
Total distance
TIME
Time*
MAX
Maximum speed
AVG
Average speed
ERROR
MESSAGES Code Cause of the problem
0X0000 no error
0X0001 controller power tube or over current
0X0002 controller over heat
0X0004 motor phase
0X0008 motor hall
0X0010 motor over heat
0X020 low voltage protection
0X0040 stall protection
0X0080 throttle
0X0100 over-speed beyond control
0X0200 battery communiction
0X0400 pas sensor
0X0800 speed sensor
0X1000 display communication
If the error remains or a different one shows, contact your seller.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Apache E-Bikes 2020 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info