670185
6
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
CONCEPT1 RS232 COMMUNICATION
WWW.APART-AUDIO.COM
INFO@APART-AUDIO.COM
Restore Factory Settings
The factory sengs can be restored with the following instrucon: “SET RESTORE ON<CR>”. The Concept1 will
reply with “Please Cycle Power!<CR>”, the output will be muted and the display will show “RESET”. The user must
power o and power on the amplier. During power on, the factory sengs will be restored.
Standby
The amplier can be set in Standby mode with the (oponal) IR remote control or with the SET STANDBY ON
instrucon. Leaving Standby mode can also be done with IR remote controller or the SET STANDBY OFF instrucon.
If an RS-232 instrucon is given when the amplier is in Standby mode or during power on and the amplier is not
ready, it will answer with “STANDBY ON”. Please wait unl the amplier is operaonal.
Power down
During power down, all sengs are stored in the memory of Concept1. Aer this, a string “POWER DOWN!<CR>”
will be send. Depending on how much variables that need to be stored, possible, there is not enough me to send
this complete string.
Errors
The following error strings may be sent by Concept1:
ERROR: Command Unknown!<CR> : Wrong spelling of command or command started with Back Space
character.
ERROR: Unknown Aribute! <CR> : Wrong spelling of aribute.
ERROR: No Header! <CR> : When HEADER is on and ECHO is o, each instrucon must be started
with header. See “RS-232 Sengs”.
ERROR: Unknown Instrucon! <CR> : A command was used with an aribute that does not support this. E.g.
SET SERIAL 0001<CR>
ERROR: Value Invalid! <CR> : A value was out of range or illegal.
ERROR: Zone Invalid! <CR> : No valid zone was specied. Valid zone names are ZONE1 and ZONE2,
without space between ZONE and its number.
ERROR: AMPLIFIER PROTECT! <CR> : See user manual (or appendix)
ERROR: OVER TEMPERATURE! <CR> : See user manual
Appendix
The instrucons SET IPGAIN … and SET SOURCENAME … will write a value to the internal memory of the Concept1.
When these instrucons are given, please wait for the reply or put a delay of at least 100ms aer this instrucon.
The ampliers with Hardware Version number ACPT 1V04 could possible send “ERROR: AMPLIFIER PROTECT!<CR>”
when they are powered o. This is because the sense circuit of the amplier reacts very fast. This doesn’t mean
there is something wrong with the amplier.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Apart Concept 1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Apart Concept 1

Apart Concept 1 Bedienungsanleitung - Englisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info