1. Plug internet cable in the network connector(RJ-45)
of Wi-Reader Pro.
2. Switch Wi-Reader Pro to ” ” (WiFi mode.)
3. Go to Setting – WiFi and select Wi-Reader Pro_xxxxxx
(6-digit combination) of iDevice(iPad, iPhone, iPod touch).
4. Open the broser of iDevice and
go to 10.10.1.1
5. Tap on “Settings” on the up-right
of the page.
6. Select “Gateway” and
tap on Next.
7. LAN Interface Setup: please tap
on Next.
8. WAN Interface Setup:
a. If get on Internet through internet cable at
a hotel room, pleased select the default
“DHCP Client” and tap on Next.
b. If get on internet through ADSL modem,
please select PPPoE and fill in username/
password provided by ISP(Internet Service
provider.) Then tap on Next.
9. Wireless Basic Settings: you can
change SSID of Wi-Reader Pro here
or tap on Next directly.
10. Wireless Security Setup: you
can set the password of WiFi
here or tap on Next directly.
11. Complete Setting: please wait for the
Wi-Reader Pro reboot. After reboot
you may to go to Settings- WiFi and
reconnect to Wi-Reader Pro_xxxxxx.
12. Enjoy the wireless network.
Super easy-to-use
wireless card reader
Create a WiFi hotspot in minutes
1. Download Wi-Reader App on
Apple App Store.
2. Plug USB flash drive / SD card, and
switch Wi-Reader Pro to “”(WiFi mode)
till the blue led is flickering.
3.
Go to Setting – WiFi and select Wi-Reader
Pro_xxxxxx(6-digit combination) of iDevice
(iPad, iPhone, iPod touch).
4. Tap on Wi-Reader App; you can browse your
files now. Support file formats:
Video：M4V / MP4 / MOV
Music：MP3 / WAV / AAC
Picture：JPG / BMP / PNG / GIF
Document：PDF / DOC / PPT / TXT / HTM/XLS
If they are picture files, you can
download the files to Photos on
iPad /iPhone or Collections
section of Wi-Reader App
Tap on Collections of Wi-Reader
App; select the files you want to
upload to SD card / USB flash drive.
You can download selected files
from SD card/ USB flash drive to
Collections section of Wi-Reader App.
You can choose to upload from
Camera Roll; upload pictures tool
by iPad, iPhone, and iPod touch.
Choose a location you want
to upload files.
Tap on “Done.” The upload
progress will start immediately.
6. Upload files
For continuous
usage, please power
Wi-Reader Pro with
USB power adapter.
5. Download files
iOS
DW17DW17
Please go to www.apotop.com.tw
Product Center for complete User Manual.
Wi-Reader Pro
4. Tap on Wi-Reader Pro App; you can
browse your files now. Support
file formats:
Video：to watch videos in
Wi-Reader Pro App, please
download MX Player or
MoboPlayer on Play Store.
Music：MP3 / WAV / AAC
Picture：JPG / BMP / PNG
Document：For HTC/ Samsung
Android Phone: please
use built-in Polaris office;
other Android Phones
please download OliveOffice
on Play Store.
Tap on Collections of Wi-Reader App;
select the files you want to upload to
SD card / USB flash drive.
You can download selected files from SD card/
USB flash drive to Collections section of
Wi-Reader Pro App. Tap the icon ” ” on
top-right; you can select the files you want
to download.
Tap on “Upload” from Smartphone.
Tap on the files you want to
upload; choose a location you
want to upload the files.
Tap on “Upload.” The upload
progress will start immediately.
6. Upload files
5. Download files
DW17DW17
Android
For Android OS User
Micro-USB port:
•for PC as a standard
card reader.
•for recharging built-in
battery.
Reset Button
Function switch:
for enabling WiFi mode.
for powerbank function.
RJ-45 cable
Support
SD card
Support
USB Flash drive
Micro-USB port:
•for PC as a standard
card reader.
•for recharging built-in
battery.
Reset Button
Function switch:
for enabling WiFi mode.
for powerbank function.
RJ-45 cable
Support
SD card
Support
USB Flash drive
Super easy-to-use
wireless card reader
1. Download Wi-Reader Pro
App on Google Play Store.
2. Plug USB flash drive /
SD card, and switch
Wi-Reader Pro to ” ”
(WiFi mode) till the blue
led is flickering.
3. Go to Setting-WiFi and
select Wi-Reader Pro_xxxxxx
(6-digit combination) of
Android Device.
8. WAN Interface Setup:
a. If get on Internet through internet cable at
a hotel room, pleased select the default
“DHCP Client” and tap on Next.
b. If get on internet through ADSL modem,
please select PPPoE and fill in username/
password provided by ISP(Internet Service
provider.) Then tap on Next.
9. Wireless Basic Settings: you can
change SSID of Wi-Reader Pro here
or tap on Next directly.
10. Wireless Security Setup: you
can set the password of WiFi
here or tap on Next directly.
11. Complete Setting: please wait for the
Wi-Reader Pro reboot. After reboot
you may to go to Settings- WiFi and
reconnect to Wi-Reader Pro_xxxxxx.
12. Enjoy the wireless network.
4. Open the broser of Android Device
and go to 10.10.1.1
5. Tap on “Settings” on the up-right
of the page.
6. Select “Gateway” and
tap on Next.
7. LAN Interface Setup: please tap
on Next.
Create a WiFi hotspot in minutes
For continuous
usage, please power
Wi-Reader Pro with
USB power adapter.
Please go to www.apotop.com.tw
Product Center for complete User Manual.
1. Plug internet cable in network
connector (RJ-45) of
Wi-Reader Pro.
2. Switch Wi-Reader Pro
to ” ” (WiFi mode.)
3. Go to Wi-Fi Setting and select
Wi-Reader Pro_xxxxxx
(6-digit combination) of Android
Phone/ tablet.
After complete selecting files, please tap the
icon ” ”on the top-left. The function menu
will be shown for Download,Export, Rename,
Move, or Delete the selected files.
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.Reorient the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
4.Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception.
It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
CAUSION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.Reorient the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
4.Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception.
It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
CAUSION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Brauchen Sie Hilfe? Stellen Sie Ihre Frage.
1
Forum
apotop-dw17---wi-reader-pro
Suche zurücksetzen
Warum geht der wi–Reader pro nicht auf ios11 kann die App nicht herunterladen vorher mit iOS 10 ging es? Eingereicht am 29-10-201711:59
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Apotop DW17 - Wi-Reader Pro wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
