Bedienungsanleitung Arada Ecoburn Plus Gas (Seite 33 von 40) (Englisch)

813452

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Press the set button again to see the temperature setting that is set and the mode (the default is 24 C ) and

on the left of the display is a sun symbol showing it’s the day temperature.

If a different set temperature is required, while the display is showing this set temperature , press the + and

– buttons to alter the setting. When finished either press set or leave and after a few seconds the new

setting will be accepted and the display will return to the time of day screen.

On the anniversary of the net minute of the clock, the set temperature will be compared to the actual

temperature displayed on the handset (i.e. the room ambient temperature around the handset). If the room

temperature is higher than the set temperature the fire will not light until the room has cooled to below the

set temperature. The fire would then automatically turn itself on when the room is cooler than the set

temperature and down and off if necessary when it is hotter than the set temperature.

(Note- when the set temperature is reached while the fire is in operation, the fire reduces the burner power

level each minute until the burner is off. The pilot will remain on for a further 30 minutes and if the set

temperature is still too high , the pilot will then also extinguish. When the set temperature is higher than the

actual temperature , the fire will automatically light and go to the full burner rate to reheat the room back to

the set temperature.

Note: If at any time the power button is operated during Thermostat mode, the control will cancel any

thermostat operation and return the control to manual mode.

For ease of setting there are two other modes that can be selected as stated above. Night mode (moon

symbol) and frost protection setting (a snow flake). These can be selected (and adjusted if necessary) by

pressing set then mode while in thermostat mode. Pressing mode button toggles through from day to frost

modes. The purpose of these settings is to help your fire to automatically protect you home against

becoming too cold if there is a sudden change in the weather. The control must be left in the appropriate

mode for this to function.

Note: As stated in an earlier section, snooze function can also be operated in conjunction with thermostat

mode. The thermostat symbol and the Zzz symbol will be on together when in this mode.

Timed thermostat mode (Closed fires Only)

This mode enables the various day, night and frost thermostat modes to be set on a program timer. The

control will work as a thermostat switching between the day, night and frost temperature settings in line with

the program set.

The set up of the timer will be shown by a demonstration.

To set up the timed thermostat to be at 24 C from 06:00 to 09:00 then drop to 18 C from 09:00 to 15:30 and

then 24 C again from 15:30 until 23:30 and then to protect from frost a 5 C setting between 23:30 to 06:30

the next day from Monday to Friday this is what you would do:-

Hold handset to unlock – press set and hold until a beep and release. Press MODE button until the timer

symbol is flashing on the top of the display – press set to enter the time mode – ‘Mo’ is flashing so it is

already set for Monday - press SET and release now press the + and – buttons to make the time of day

read 06:00 (note the steps are in 15 minutes steps) – press SET and release- press + and – to make the

next symbol show a flashing sun symbol- press and release SET- as Mo is flashing press and release SET

again enter the next time of 09:00- press and release SET- change the flashing sun symbol to a flashing

moon symbol by pressing and releasing the + and – buttons then press and release SET again to store the

moon setting (18 c)- continue this until you have entered each time and temperature change required for

each day.

To put the fire into thermostat timer mode press and release the mode button until the thermostat and timer

symbols are displayed on the display at the top. Press and release the “SET” button and the control will

now run the timed program set up in the memory.

BK 710 Page 33

ECOBURN PLUS GAS - USER INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arada Ecoburn Plus Gas Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info