Bedienungsanleitung Arcam A19 (Seite 11 von 86) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

578718

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

E-9

English

loudspeakers

Notes on making speaker

connections

< Do not make any connections to any amplier

while it is switched on. We recommend that

your amplier is completely disconnected from

the mains supply before starting.

< Before switching your amplier(s) on for the

rst time aer connecting to speakers, please

check all connections thoroughly. Ensure that

bare wires or cables are not touching each other

or the amplier’s chassis (which could cause

short circuits), and that you have connected

positive (+) to positive and negative (–) to

negative. Be sure to check the wiring for both

the amplier and the speaker.

< Aer making connections: switch the

amplier(s) on, select a source signal, then

gradually increase the volume to the required

listening level.

< If you are unsure as to how your system should

be connected, or need advice on bi-amping,

please contact your Arcam dealer who will be

happy to help you.

Single wiring

Single wiring is the conventional wiring method of

running a single cable per channel between the amplier

and the speaker; this is the easiest technique.

If each speaker has more than one pair of connecting

terminals, use the terminals labelled LF or ‘Low

Frequency’ for each speaker.

Connect the positive terminal of the right speaker

connection on the amplier (coloured red and labelled

+R) to the positive terminal of your right speaker.

Bi-amping

Bi-amping is the separation of the amplication of low-

and high-frequency signals over two ampliers.

Bi-amping requires the use of two ampliers per

channel. Normally, your A19 is used to drive the high-

frequency (treble) speakers, with a P38 used for the

lower (bass) frequencies.

Connect your A19 to the speakers as described for

single wiring, with the exception that the A19 should

be connected to the speaker terminals labelled HF or

‘High Frequency’. en connect the power amplier

(an Arcam P38 for example) to the LF or ‘Low

Frequency’ terminals, as in the diagram. A pair of audio

interconnect cables are also required to connect the

pre-amp outputs of the A19 to the power amp inputs of

the P38.

An A19 connected to speakers using single wiring

Arcam A19

An A19 and P38 connected to speakers using bi‑amping

Arcam A19

Arcam P38

Similarly, connect the negative terminal of the amplier

(coloured black and labelled with R–) to the negative

terminal of your speaker. Repeat the process for the le

speaker, using the amplier terminals labelled +L and L–.

If your speakers support bi-wiring, then there is a strip

of conductive metal on the speakers connecting the low-

frequency terminals to those for the higher-frequencies;

this MUST NOT BE REMOVED in a single-wired

system.

Note that the strip of metal on the speakers connecting

the lower terminals to the upper terminals MUST BE

REMOVED. Failure to do so will result in damage to

both ampliers, which will not normally be covered

under warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam A19 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info