Bedienungsanleitung Arcam A28 (Seite 10 von 17) (Englisch)

578744

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

E-10

Switching the A28 on

e POWER button switches the unit on and o;

alternatively, the unit can be switched in and out of

stand-by mode by pressing the

button on the remote

control handset.

e power light (next to the ‘A28 Integrated Amplier’

text) indicates the state of the amplier:

1. A red light means that the amplier is in stand-by

mode;

2. When you switch your amplier on, the power

light glows amber for a few seconds; during this

time the outputs are muted;

3. e light changes to green when the amplier is

ready for use.

e power light may ash if a fault has occurred –

the fault type is shown on the display. See page 15,

‘Troubleshooting’, for help in resolving fault situations.

If the fault cannot be cleared, unplug your amplier and

contact your Arcam dealer.

Changing the volume

Use the control knob to change the volume. Turn the

knob clockwise to increase the volume, anti-clockwise

to reduce it.

e output of the A28 can be silenced by pressing MUTE

on the front panel or remote control. Press MUTE for a

second time (or change the volume) to cancel the mute.

SP1 and SP2

ese buttons allow you to switch the main speakers

(connected to the lower set of speaker terminals) and

secondary speakers (connected to the upper set of

speaker terminals) on and o.

e light above each button glows if the corresponding

speakers are currently selected. If you have connected

the A28 to the speakers using the single-wired

conguration described on page 9, then the SP1 light

should be illuminated; if you have used the bi-wiring

conguration described on page 9, both SP1 and SP2

must be switched on. Note that when both lights are o,

the amplier will appear not to work, as all speakers are

disconnected.

When listening to ‘loud’ inputs, such as CDs, the

amplier may reach its full power before the display

shows 72 (maximum volume), in contrast, lower-level

inputs, such as tuners, will sound quieter for the same

volume level shown. To compensate for this, the input

levels of each source may be adjusted. is can be done

using the A28 setup menu (see page 11).

operation

Selecting an audio source

A source-selection button is used to select the source

that is connected to the input corresponding to the

button.

Listening using headphones

e headphones socket (PHONES) accepts headphones

with an impedance rating between 8Ω and 2kΩ, tted

with a 6.5mm stereo jack plug.

e pre-amp. outputs and speakers are muted when

headphones are plugged in. e headphones socket is

always active, unless the volume has been muted.

Balance

In addition to the A28 setup menu (see page 11), you

can also set le-right stereo balance directly by pressing

the front-panel BALANCE button and adjusting the

balance with the control knob.

Display

e DISPLAY front panel button changes the display

brightness. ere are three brightness levels: ‘on’,

‘dimmed’ and ‘o’. If the A28 is switched o while the

display is set to ‘o’, the display is set to ‘dimmed’ when

the A28 is switched on again.

Recording an audio source

e A28 allows listening to and recording from the

same source, or listening to one source whilst recording

another. e signal to be recorded is sent to both the AV

and AUX output sockets.

Selecting the source for recording

e recording outputs can be congured in two ways:

1. To record the source being listened to;

2. To record a particular (specied) source,

regardless of what is being listened to.

To record the source being listened to, press the

RECORD button and turn the control knob if necessary

until the display shows ‘REC SRC’. Aer a few seconds,

the display reverts to showing the volume level, and you

are ready to record. In this conguration, selecting a

dierent input changes the source that is routed to the

recording outputs.

To record one source whilst listening to another, press

RECORD and turn the control knob until the display

shows ‘Rec ’ followed by the name of the input (Sat,

Phono, CD, Tuner, AUX or DVD) that you wish to

record from. You are now ready to record.

Press a dierent source button to change the source that

you wish to listen to – this does not alter the source that

is routed to the recording outputs.







  













 

av-ph 20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam A28 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam A28

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info