Bedienungsanleitung Arcam AV888 (Seite 33 von 74) (Englisch)

482343

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

E-31

English

AMP

AMP Device Mode

e

Device Mode button congures the CR102

to control the AVR500/AVR600/AV888. Pressing this

button does not aect the currently selected input on the

AVR500/AVR600/AV888.

IMPORTANT: e CR102 must also be in

AMP Device

Mode to control the following sources: PHONO, MCH

(multichannel analogue), AUX, NET (optional network

audio), USB, IPOD (for use with the optional Arcam

rLead or rDock).

However to control the internal Tuner in the AVR500/

AVR600 (AM/FM/DAB or Sirius if tted), the CR102

must rst be in

TUN Device Mode (see later).

e functionality of the CR102 is context sensitive for

the internal sources and is described in the following

table.

Single press – Toggles AVR500/AVR600/

AV888 power between standby and on

in the current zone (zone in which the

command is received).

Press and hold – Forces all AVR500/

AVR600/AV888 zones into standby,

regardless of which zone the command was

received in.

…

e number keys can be used for source

selection (without changing the CR102

Device Mode). Alternatively the Device

Mode buttons can also be used with the

SHIFT key.

SAT (satellite) input

PHONO input

AV input

TUNER input

DVD input

TAPE input

VCR input

CD input

AUX (front panel) input

MCH (multichannel) input

PHONO

Selects Tape input on the AVR500/AVR600/

AV888

SHIFT +

selects PHONO input on the

AVR600/AV888

RPT

(for

IPOD and NET sources)

Modies many keys (see individual key

descriptions below).

AUX

Selects

MCH (multichannel) input on the

AVR500/AVR600/AV888

SHIFT +

selects AUX input on the

AVR500/AVR600/AV888

Navigate menus

OK conrms a setting (equivalent to ‘Enter’

or ‘Select’ on some remote controls)

Press and hold

OK to force the analogue

and digital video outputs to the default

resolution: 480i (525-line NTSC).

SHIFT +

decreases the picture resolution.

SHIFT +

increases the picture resolution.

SHIFT +

turns current zone (in which

command is received) on

SHIFT +

turns current zone (in which

command is received) o.

NET

Selects

IPOD input on the AVR500/AVR500/

AVR600/AV888

SHIFT +

selects network (NET) internal

input on the AVR500/AVR600/AV888

(where tted).

Cycles through the available surround and

downmix modes.

Displays the AVR500/AVR600/AV888 setup

menu on the On Screen Display (see page

34).

Cycles through the front panel display’s

brightness options

Toggles the mute function of the AVR500/

AVR600/AV888

] [

(track control for

IPOD and NET sources)

SHIFT +

[

Follow Zone1 source.

When the command is received in Zone2

or Zone3, the source for that zone follows

whatever input source is selected in Zone1

- +

Decrease () and increase (+) AVR500/

AVR500/AVR600/AV888 volume

DIRECT

)

Stereo direct on/o. Provides a direct

analogue path from the analogue inputs to

the le and right front outputs. Switches o

any surround processing modes and shuts

down the DSP circuits for the best stereo

sound quality.

Displays the room EQ settings menu

EFFECT

(for

IPOD and NET sources)

BASS

(

Calls up a pop-up (and front screen) to

adjust the bass setting for a particular input.

TRIm

Brings up the speaker trim menu.

Use the

and

navigation

buttons. Press TRIM again to exit the speaker

trim menu.

As this is a temporary adjustment, these

additional trim levels are reset to zero when

the unit is turned o or put into standby,

but are retained if the selected input is

changed. ese temporary trim levels are

independent of the speaker levels found in

the setup menu.

SyNC

Delays may be introduced into the video

signal by video processing which causes

a mismatch between the audio and video

timing. You will notice this by speech sound

being out of synchronization with the lip

movements in the video.

To compensate for this, you can adjust the

lip sync delay. Press the

SYNC button and

use the

and

navigation buttons. Press

again to exit the lip sync trim menu.

SUB

Brings up the subwoofer trim menu. Use

the

and

navigation buttons. Press SUB

again to exit the sub trim menu

TREBLE

Calls up a pop-up (and front screen) to

adjust the treble setting for a particular

input.

FAV+

(for

IPOD and NET sources)

FAV-

(for

IPOD and NET sources)

HOmE

(for

IPOD and NET sources)

INFO

Cycles through the information displayed

on the lower le portion of the front panel

display.

iPod commands

e iPod interface is selected by pressing

in AMP

Device Mode on the CR102. When connected to an

iPod via an optional rLead/rDock, the keys below are

used to navigate music les in AMP Device Mode.

Navigate the files on screen.

OK selects/play the highlighted file.

RPT

Toggles random (shuffle) play of the playlist

on and off.

SHIFT +

cycles through the repeat options

] [

Selects the previous/next track in the

current playlist

Begins or resumes playback at the currently

highlighted track

Toggles pause and playback of the current

track

Stops playback

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam AV888 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam AV888

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info