Bedienungsanleitung Arcam AV888 (Seite 63 von 74) (Englisch)

482343

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

E-61

English

Problem Check that...

Sound only comes from some

of the speakers

you have an appropriate surround source selected and playing.

the DVD disc is encoded in the appropriate format, and the correct format

has been selected in the disc start menu of the DVD player (if applicable).

the DVD player has been set to output ‘bitstream’ audio on the digital

output.

the display window indicates that the disc you are playing is a multichannel

recording (you may need to press the INFO key several times until you get to

the ‘incoming format’ display).

all the speakers are correctly connected to the speaker terminals and are

secure.

you have not selected ‘Stereo’ as the decoding mode.

your speaker balance is correct.

you have congured the unit to include all the speakers in your system.

Unable to select Dolby Digital

or DTS decoding modes

e AVR500/AVR600/AV888 can only apply Dolby Digital and DTS decoding

to sources which have been encoded in the same format.

Check that:

digital source is selected and connected.

the source is playing appropriately encoded material.

the DVD disc is encoded in the appropriate format and that the correct

format has been selected in the disc start menu of the DVD player (if

applicable).

the DVD player has been set to output ‘bitstream’ audio on the digital output

(not PCM).

When playing a Dolby Digital

DVD, the AVR600 selects

Dolby Pro Logic

you have a digital connection from your DVD player.

sometimes Dolby Digital DVD discs contain material at either the beginning

or the end of the main movie that is not in full 5.1 format, but in two-

channel or Pro Logic decoding.

Hum on the analogue input

all cables are making a good connection. If necessary withdraw the cable

from the connector and plug it fully in again (turn the power o before

doing this).

the connections inside the source cable connector are not broken or badly

soldered.

if the hum originates only when one particular source component is

connected, that an aerial cable, or dish connection to this source is ground

isolated. Contact your installation contractor.

ere is radio or television

reception interference

where the interference is coming from. Switch o each source component in

turn, then any other equipment. Most electronic equipment does generate

low levels of interference.

try re-arranging cabling from the nuisance source away from other cabling.

ensure that the cabling used is high quality, specied for its purpose, and is

properly screened.

if the problem persists, contact your dealer.

Problem Check that...

e source switching changes

randomly or freezes on one

source

there are no static or impulse interference problems caused by nearby power

equipment switching, e.g., heating or air conditioning control. Switch the

unit o, wait ten seconds, then switch it on again to clear an operating

problem. Contact your installer if the problem returns or persists.

there is no direct sunlight shining on the infra-red detector behind the front

panel display.

Volume is always too loud

when I turn on

the ‘max on volume’ setting is not set too high.

When Zone2 or 3 is put into

standby, the main zone is also

switched o

the ‘zone standby‘ setting in the setup menu is set to LOCAL.

When a USB memory device is

connected, ‘USB’ is not shown

in the network client’s list of

folders

a USB memory device is connected that conforms to the mass storage class.

a USB hub is not being used.

If les on a USB memory

device cannot be played:

the USB device is formatted in FAT16 or FAT32.

the USB device does not have multiple partitions.

the les are in a compatible format.

If les on a computer cannot

be played

the les are in a compatible format.

the computer is connected via a network and not USB – the AVR500/

AVR600/AV888 USB port cannot be used for a direct connection to a

computer

If you cannot connect to a

wired network

the Ethernet cable you are using is correctly connected between the

AVR500/AVR600/AV888 and the network hardware.

the network is set up for xed IP addressing and you have the AVR500/

AVR600/AV888 set to use DHCP.

the network is set up for DHCP and you have the AVR500/AVR600/AV888

set to use xed IP addressing.

If you cannot connect to a

favourite internet radio station

the station is still broadcasting or is not congested – try again later.

If the internet radio station

sound quality is poor or

broken

the radio station does not have a low bit rate (use the INFO key to nd this or

look on the OSD).

the network is not slow or congested.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam AV888 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam AV888

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info