Bedienungsanleitung Arcam AVR500 (Seite 7 von 74) (Englisch)

482341

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

E-5

English

Placing the unit

< Place the unit on a level, rm surface, avoiding

direct sunlight and sources of heat or damp.

< Do not place the unit on top of a power amplier or

other source of heat.

< Do not place the unit in an enclosed space such as

a bookcase or closed cabinet unless there is good

provision for ventilation. e unit will run warm

during normal operation.

< Do not place any other component or item on top of

the amplier as this may obstruct airow around the

heat-sink, causing the amplier to run hot. (e unit

placed on top of the amplier would become hot,

too.)

< Make sure the remote-control receiver on the front

panel display is unobstructed, otherwise this will

impair the use of the remote-control. If line-of-sight

is impractical, a remote-control repeater can be used

with the rear panel connector (see page 17).

< Do not place your record deck on top of this

unit. Record decks are very sensitive to the noise

generated by mains power supplies which will be

heard as a background ‘hum’ if the record deck is too

close.

Power

e amplier is supplied with a moulded mains plug

already tted to the lead. Check that the plug supplied

ts your supply – should you require a new mains lead,

please contact your Arcam dealer.

If your mains supply voltage or mains plug is dierent,

please contact your Arcam dealer immediately.

e amplier can be switched for operation between

220–240V (switch position 230V) and 110–120V

(switch position 115V).

NOTE

Ensure that the unit is switched o and the power

lead removed before changing the position of the

voltage range switch.

Push the IEC plug end of the power cable into the

socket on the back of the amplier, making sure that it

is pushed in rmly. Plug the other end of the cable into

your mains socket and, if necessary, switch the socket

on.

e amplier can be turned on using the

POWER switch

on the front panel. While switched on, the front panel

LED will glow green.

Standby power

e unit can be switched into standby mode using

the

button on the CR102 remote control. While in

standby mode the front panel LED will glow red and

power consumption is around 3 watts.

While in Standby mode, it may be possible to hear a

slight residual hum coming from the mains transformer

inside the amplier. is is perfectly normal. However,

if the unit is to be le unused for an extended period,

we recommend that you disconnect it from the mains

supply to save power.

Interconnect cables

We recommend the use of high-quality screened cables

that are designed for the particular application. Other

cables will have dierent impedance characteristics

that will degrade the performance of your system (for

example, do not use cabling intended for video use to

carry audio signals). All cables should be kept as short

as is practically possible.

It is good practice when connecting your equipment to

make sure that the mains power-supply cabling is kept

as far away as possible from your audio cables. Failure to

do so may result in unwanted noise in the audio signals.

For information on speaker cabling, please refer to the

‘Speakers’ section, beginning on page 23.

Radio interference

e AVR500, AVR600 and AV888 are audio devices

containing microprocessors and other digital

electronics. ey have been designed to very high

standards of electromagnetic compatibility.

is is a Class A product. In a domestic environment

this product may cause radio interference, in which case

the user may be required to take adequate measures.

If the unit causes interference to radio or television

reception (which can be determined by switching the

unit o and on), the following measures should be

taken:

< Re-orient the receiving antenna or route the antenna

cable of the aected receiver as far as possible from

the unit and its cabling.

< Relocate the receiver with respect to the unit.

< Connect the aected device and the unit to dierent

mains outlets.

If the problem persists, please contact your Arcam

dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam AVR500 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam AVR500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info