Bedienungsanleitung Arcam C31 (Seite 5 von 16) (Englisch)

578750

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

C31/P38/P1

E-4

English

C31/P38/P1

E-5

Recording loops

The C31 is equipped with two recording loops, for use with recording devices (such as cassette decks,

MiniDisc players, VCR’s etc.)

TAPE/PROC RECORD OUT – Connect these output sockets to the input sockets of your recording

device (usually labelled RECORD or IN).

TAPE/PROC PLAY IN – Connect the output sockets of your recording device (usually labelled PLAY

or OUT) to these inputs.

If you do not have a recording device, you can use this input for other (line-level) equipment, such

as a CD-player, tuner, VCR, etc.

VCR/TAPE2 RECORD OUT – These output sockets can be connected to the input sockets of a

second recording device.

VCR/TAPE2 PLAY IN – Connect the output sockets of your second recording device to these

inputs. Alternatively, this input may be used for other (line-level) equipment such as a CD-player,

tuner, etc.

Power-amplier connections

456

PRE OUT – The recommended connection between the C31 pre-amplier and your power

amplier depends on both the distance between the two and the type of power amplier that you are

using. There are three options:

1. If the cables to be used to connect the C31 to the power amplier are less than 3m long, we

recommend connecting the DIRECT sockets

to the input sockets of your power amplier. On the

P38 and P1, connect to the socket(s) labelled AUDIO IN.

If the cables to be used to connect the C31 to the power amplier are 3m or longer, then the connection

to use depends on the type of power amplier you have.

2. If your power amplier does not have balanced inputs (such as the P38), use the BUFFERED

outputs

. On the P38, connect to the sockets labelled AUDIO IN.

3. If your power amplier provides balanced inputs (such as the P1), use the balanced outputs

. On

the P1, connect to the sockets labelled BALANCED AUDIO IN.

The buffered and balanced outputs are designed to drive longer cables than the direct output, but you

cannot damage either your C31 or your power amp. by using the “wrong” connection type.

Other connections

Phono earth terminal – For connecting your turntable earth lead (if required). Note that this terminal

must not be used as a safety earth.

TRIG OUT and REMOTE IN (12V in and out) – These connections are intended for use in multi-

room installations.

TRIG OUT: This output provides a 12V signal whenever the unit is switched on (i.e.,

not off or in stand-by). This signal can be used to switch on power ampliers (or other

equipment) connected to the C31, as they will come on when the C31 is activated. This is

useful if the power amplier is remote from the C31, or otherwise difcult to access.

REMOTE IN: This allows remote-control signals to be received by the C31 if the remote

sensor is covered (or otherwise not ‘visible’ to the remote-control). An external sensor

(such as the Xantech ‘Dinky Link’™) is used to receive the signals from the remote-control,

which are then fed to the C31 (into this input) using a suitable cable.

In normal use there is no need to make any connections to either of these sockets.

Connecting to a power supply

Mains lead

The appliance is normally supplied with a moulded mains plug already tted to the lead. Check

that the plug ts your supply and that your mains supply voltage agrees with the voltage

setting (115V or 230V) indicated on the rear panel of the unit

before plugging in.

If your mains supply voltage or mains plug is different, please consult your Arcam dealer

immediately.

Plugging in

Push the IEC-plug of the power cable into the socket POWER INLET

in the back of the unit,

making sure it is pushed in rmly.

Stand-by power

For remote stand-by operation, the amplier’s control power-supply is kept powered up all the time the

unit is connected to the mains supply. The front-panel power-switch powers all other circuitry down and

power consumption in this mode is less than 2W.

This means that even though the power-switch is off, it may be possible to hear a slight residual hum

coming from the mains transformer inside the amplier. This is perfectly normal. If the unit is to be left

unused for an extended period, however, we recommend that it is disconnected from the mains supply.

The 12V-trigger uses

a 3.5mm mono jack

plug, wired as follows:

Sleeve: Ground

Tip: Active

When the C31 is

powered-on, the tip

carries 12V, current-

limited to 30mA; other-

wise the tip carries 0V.

The remote-in also uses

a 3.5mm mono jack

plug, wired as above.

Remote control signals

must be in modulated

RC5 format, with a

voltage level of 5–15V.

Note that the remote

receiver will require its

own power-supply.

Details of the

Xantech ‘Dinky Link’

can be found at

www.xantech.com, or

ask your dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam C31 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam C31

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info