Bedienungsanleitung Arcam DiVA A70 (Seite 5 von 12) (Deutsch, Englisch, Holländisch, Französisch)

578756

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

English

A70

E-5

Standby power

For remote standby operation, the amplifier’s control power supply is kept powered up all the time the

unit is connected to the mains supply. The front panel power switch powers down all other circuitry.

Power consumption in this mode is less than 2.5W.

This means that even though the power switch is off, it may be possible to hear a slight hum coming

from the mains transformer inside the amplifier. This is perfectly normal. If the unit is to be left unused

for an extended period, we recommend that it is disconnected from the mains supply by switching it off

at the wall socket, or by disconnecting the power lead.

Connecting to other equipment

The use of high quality interconnect cables to and from your amplifier is recommended to ensure the

best sound quality. Sockets marked L (and R) on your amplifier should only be connected to sockets

marked L (and R) on other equipment. All the line inputs have the same sensitivity and may be used

with equipment other than that labelled, if needed.

LINE OUT

– Connect this output to the audio inputs of any unit with a line-level input, e.g., tape

deck, etc.

TAPE/RECORD OUT

– Connect these output sockets to the input sockets of your cassette deck

(usually labelled RECORD).

TAPE/PLAY IN

– Connect these input sockets to the output sockets of your cassette deck

(usually labelled PLAY). If you do not have a cassette deck you can use this input for other (line level)

equipment, such as a CD player, tuner, VCR, etc., but not a turntable.

DVD

– Connect this input to the audio outputs of a DVD player.

– Connect this input to the audio outputs of audiovisual equipment such as a VCR, laserdisc

player, satellite or Nicam tuner.

TUNER

– Connect this input to the audio outputs of your radio tuner.

– Connect this input to the audio outputs of your CD player or DAC (digital to analogue

converter).

AUX

– Connect this input to the audio outputs of any unit with a line level output, e.g. tape deck,

tuner, etc.

PHONO

– Connect this input to the output of your record player. This input provides RIAA

equalization and is compatible with most high output moving magnet (MM) cartridges.

Phono earth terminal – For connecting your turntable earth lead (if fitted). Note that this terminal

must not be used as a safety earth.

TRIG OUT and REMOTE IN

(12V in and out) – Each socket accepts a 3.5mm Mono Jack, with

Tip=signal, Sleeve=ground. The connections are intended for use in multi-room installations.

TRIG OUT – This output provides a 12V signal whenever the unit is switched on (i.e., not off or

in standby). This signal can be used to switch on automatically power amplifiers (or other

equipment) connected to the A70, as they will come on when the A70 is activated. This is useful if

the power amplifier is remote from the A70, or otherwise difficult to access. If you are bi-amping

with a power amplifier and wish to power both units on or off simultaneously, see page 10.

REMOTE IN – This allows remote control signals to be received by the A70 if the remote sensor is

covered (or otherwise not ‘visible’ to the remote control). An external sensor is used to receive

the signals from the remote control, which are then fed to the A70 (into this input) using a

suitable cable. Remote control signals acceptable to the A70 must be in modulated RC5 format,

with a voltage level of between 5V and 15V.

Note that in normal use there is no need to make any connections to these sockets. If you would like to

make use of these features, please contact your dealer for more advice on how to make the connections

and on what type of cable to use.

Pre/power amplifier connections

If you wish to use your A70 as a power amplifier, please consult your Arcam dealer.

PRE OUT

– To use your amplifier as a pre-amplifier, connect the PRE OUT sockets to the input

sockets of your power amplifier. With a power amplifier of the correct gain (e.g. an Arcam P90 power

amplifier) you can bi-amplify (‘bi-amp’) suitable loudspeakers, giving significant improvements in sound

quality (see page 10).

The different output types

The distinction between PRE OUT, LINE OUT and RECORD OUT output types is subtle but important.

PRE OUT: This is the output that should be connected to your power amplifier. The output level varies

with the volume control.

LINE OUT: This output is taken before the volume control, i.e., the source being listened to is routed

directly to this output. If you wish, this output may be connected to a recording device, such

as a cassette recorder. Under no circumstances should this output be connected to a power

amplifier.

RECORD OUT: The output from the RECORD OUT connectors is dependent on the configuation of

the amplifier. Full instructions for this output are given on page 7; briefly, if the amplifier

is configured to ‘REC SOURCE’, then this output will carry the same signal as the LINE OUT

connection. If the amplifier is configured so that you are recording a different source than the

one you are listening to, then the RECORD OUT connections will carry the source being recorded.





3.5mm Mono Jack

Arcam DiVA A70 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info