Bedienungsanleitung Arcam DiVA AVR280 (Seite 18 von 38) (Englisch)

578769

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

AVR280

ADV 4 – Zone 2 Settings

ZONE2 VOL: Sets the volume for Zone 2.

Max Vol 20–83: Limits the maximum volume setting for Zone 2. This is a useful

feature to prevent accidental overdriving of low power-handling speakers, for example.

Fix Vol: This selects between xed and variable audio output to Zone 2. If NO is

selected, the output level can be controlled from Zone 2 or the main system. If you wish

to x the volume level, rst set the Zone 2 volume to the desired level, then select

YES.

Max On Vol: Limits the maximum volume Zone 2 operates at when it is rst switched

on. Zone 2 comes on at this volume if the last used volume exceeds this value.

Stand-by: This allows zone 1 (the main zone) to be put into stand-by, either locally

only or by Zone 2 as well.

LOCAL ONLY: Only the main zone will be switched into stand-by from the main

zone.

ALL OFF: Both the main zone and Zone 2 will be switched into stand-by from the main zone.

Access: This acts as a ‘parental control’ device to disable or enable access to sources for Zone 2.

Press the unwanted source button on the remote control handset or front panel to disable it for Zone 2.

Press again to enable the source.

Enabled sources are listed on the ‘Access:’ line of the menu page.

ADV 5 – Analogue Settings

Input trims: Allows the adjustment of the input sensitivity of the analogue inputs (in

Volts rms) so that each one achieves the optimum dynamic range and sounds similar in

loudness to the others.

Available level settings are: LOW 0.5V, MEDIUM 1V, REFERENCE 2V, HIGH 4V. The

reference level of 2V should be appropriate for most inputs.

If a source is very quiet compared with the other sources you can increase its loudness

by selecting the MEDIUM 1V or LOW 0.5V settings.

ADV 6 – HDMI Settings

The AVR280 provides two HDMI inputs; these are labelled ‘DVD’ and ‘SAT’ in anticipation

of the most common use for these connectors, but they may be used for any HDMI

source. These inputs may be congured to be associated with any of the other sources,

so that selecting that source (‘AUX’, for example), selects one of the HDMI inputs

instead of the usual input associated with that source.

NOTE: If the DVD button is assigned to an HDMI input, you will also be able to view the

HDMI signal from the DVD player if the MCH (DVD-A multi-channel) button is selected.

Saving Settings and Exit Set-up

You can either save the settings now or exit without saving the changes.

Save Set-up

1. Press

MENU to go to the ‘Set-up Menu Index’ at the ‘Save Set-up’ point.

2. Press

OK to save.

3. Press

OK to select ‘Exit Set-up’ and exit system conguration.

Exit without saving

If you choose to ‘Exit Set-up’ without rst saving the changes, then the new settings will be lost.

1. Press

MENU to go to the ‘Set-up Menu Index’ at the ‘Save Set-up’ point.

2. Press

to select ‘Exit Set-up’.

3. Press

OK when ‘Exit Set-up’ is selected to exit system conguration.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR280 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info