Bedienungsanleitung Arcam DiVA AVR280 (Seite 25 von 38) (Englisch)

578769

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

AVR280

English

FM Mute/Mono

The AVR280’s tuner has an auto-muting circuit that, when engaged, mutes any signal that is of

insufcient strength for listening. To engage this circuit press the FM MUTE/MONO button on the front

panel: ‘FM MUTE’ is shown in the display. If a signal is muted you will hear no sound through the

loudspeakers.

Should you wish to listen to a station that is ‘auto muted’ press the FM MUTE/MONO button again to

disengage the muting circuit. The tuner now switches to monoaural reception, cancelling much of the

background hiss. ‘FM MUTE’ is no longer displayed and you are able to continue listening.

Listening to the tuner in Zone 2

The tuner can be selected, as other inputs, for routing to Zone 2. Note, though, that it is not possible to

listen to different stations in the main zone and Zone 2 simultaneously. This is because the AVR280 is

tted with just a single tuner module.

Using the Main Menu

Three ‘Main Menu’ screens allow day-to-day changes to be made to the way the AVR280 operates.

Examples include adjusting the tone control for a particular input, or selection of ‘direct’ mode.

The three Main Menu screens are available on your display device. The selected line of each screen is

also displayed on the front panel of the AVR280. Each of the following sections has a picture showing the

screen that is displayed as you move through the menus.

Using the remote control to enter the Main Menu

Briey press the MENU button to enter ‘Main Menu Screen 1’. Use the navigation

and

buttons

to go up and down the menu respectively. The

and

buttons are used to alter the selection on the

highlighted line, or to change to the next screen if the menu heading is highlighted.

Using the front panel to enter the Main Menu

Press the MENU button to enter the main menu. To cycle through the items on a menu, use the

EFFECT /

button to go down and

MODE/

button to go up one line for each press. Use the volume

control knob for the

and

functions in order to cycle through the available choices, or to change the

menu page if the menu heading is highlighted.

Main Menu Screen 1

Vol: Shows the present volume being used for the main zone and can be adjusted

from here.

Audio Input: This shows the current audio input source selected. The current

audio input can be changed when this line is highlighted using the source select

buttons on the front panel or the remote. Note that changing the audio input

also changes the video input to the same setting.

Video Input: This shows the current video input source selected. The current

video input can be changed when this line is highlighted using the source select

buttons on the front panel or the remote.

Changing the video input does not change the audio input, so you can watch a

different input from the one you are listening to.

If the audio and video are set to different inputs, they will be reset to be the

same input when the audio input is next changed.

NOTE: the composite/S-video inputs and the high-quality video inputs are

independent of each other. If you are watching a video source by using the one of the

high-quality video inputs, it is not possible to change the video input independently of

the audio.

Video Type: This setting is applicable only to TVs being fed via a SCART lead where the trigger

outputs

and

are connected via suitable SCART header. It shows the video aspect ratio

currently selected for the display, which can be set manually to 4:3 or 16:9, depending on which

format you are feeding into your TV. See page 12 for further details on using these triggers.

Stereo Direct:

OFF: the AVR280 functions in its normal way.

ON: the AVR280 uses the analogue input signal for the source, bypassing the digital circuitry.

In this mode, the AVR280 functions like an analogue amplier: it also shuts down all the unused

digital circuitry for optimum stereo performance. Note that no digital output is available in this

case.

Bass and Treble: These allow you to alter temporarily the bass and treble controls for all currently

active speakers. In the case of Stereo, this would only apply to the front left and right speakers.

In Effects, Pro Logic IIx Music, Dolby Digital and DTS modes (for example), this would apply to

all present speakers.

You can adjust the bass and treble by up to ±6dB. These adjustments are in addition to those

made in ‘Speaker Eq’ in the Set-up Menu. However, the maximum overall tone control range for

each speaker using this screen plus the settings in ‘Speaker Eq’ is still ±6dB (not ±12dB).

Note that bass and treble alterations are not available in Stereo mode when AUTO STEREO TONE

BYPASS is set to YES, or in Stereo Direct mode.

Balance: To alter temporarily the sound balance between the front left and right speakers. You can

alter the sound stage to either the left or right by up to 10dB. Note that it is not possible to shift

the audio signal completely over to one channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR280 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info