Bedienungsanleitung Arcam DiVA AVR280 (Seite 32 von 38) (Englisch)

578769

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

AVR280

When playing a Dolby Digital DVD, the AVR280

selects Dolby Pro Logic:

Check that:

you have a digital connection from your DVD player.

sometimes Dolby Digital DVD discs contain material

at either the beginning or the end of the main movie

that is not in full 5.1 format, but in two-channel or Pro

Logic encoding.

Hum on an analogue input:

Check that:

all cables are making a good connection. If necessary

withdraw the cable from the connector and plug it fully

in again. (Turn the power off before doing this.)

the connections inside the source cable connector are

not broken or badly soldered.

if the hum originates only when one particular source

component is connected, that an aerial, cable or dish

connection to this source is ground isolated. Contact

your installation contractor.

try switching the ground lift switch on the back panel.

There is radio or television reception interference:

check where the interference is coming from. Switch

off each source component in turn, then any other

equipment. Most electronic equipment does generate

low levels of interference.

try re-arranging cabling from the nuisance source

away from other cabling

ensure that the cabling used is high quality, specied

for its purpose, and is properly screened.

if the problem persists contact your installer.

The source switching changes randomly or freezes on

one source:

Check that:

there are no static or impulse interference problems

caused by nearby power equipment switching, e.g.,

heating or air conditioning control. Switch the AVR280

off, wait ten seconds, then switch it on again to clear

an operating problem. Contact your installer if the

problem returns or persists.

Volume is always too loud when I turn the system on

for the main zone or Zone 2:

Check:

the ‘Max On Volume’ line of ‘General Settings’ or

‘Zone 2 Settings’ pages in the Set-up Menu. They will

need adjusting to a lower level.

You can’t select a particular input in Zone 2:

Check that:

you have not blocked that particular input using the

‘Access’ line of ‘Zone 2 Settings’ in the Set-up Menu.

When Zone 2 is put into stand-by, the main zone is

also turned off:

Check that:

the ‘Zone 2 Stand-by’ line of ‘Zone 2 Settings’ in the

Set-up Menu is set to Local Only.

Unstable OSD on screen display:

The AVR280 defaults to the NTSC video standard for US

units and PAL for European units.

If your display device is unable to display the default video

standard, attach a source component the generates the

video standard you wish to use; the AVR280 will switch

automatically to the supplied video standard when the

source is selected.

No Zone 2 audio when playing DTS lm:

Most two-channel DVD players cannot output a stereo

decoded version of the DTS signal – the analogue outputs

are muted when playing back DTS lms. If you want to

watch a DVD in both the Main zone and Zone 2, please use

the Dolby Digital sound track.

No centre image (vocal) in Zone 2 when using the

multi-channel input:

Most DVD/SACD players are unable to provide a two-channel

down-mix of source material at the same time as decoding

a multi-channel audio stream. Therefore, only the front

left and right channels from the multi-channel mix will be

available in Zone 2.

To overcome this, play the stereo mix from the DVD-audio

disc instead.

Strange aspect ratio of video in Zone 2:

Most DVD players can only decode video to one aspect ratio

at a time. For example, if you are using wide screen in the

main zone, then wide screen information will also be fed to

Zone 2.

To overcome this, either set the lm to 4:3 for the main

zone when you want to use Zone 2 as well, or change the

Zone 2 display to a wide screen capable type.

Unable to adjust bass and treble controls:

Bass and treble is not available in ‘Direct’ mode. For

Analogue Stereo and Digital Stereo modes, check that the

‘Auto Stereo Tone Bypass’ line of ‘Speaker Eq’ in the Set-up

Menu is set to NO.

Digital signal drops out when other electrical

appliances turn on (heating, fridge, freezer, etc.):

If a poor quality or incorrect type of cable has been used for

the digital inputs, they can pick up electrical noise. Change

the cable to a 75Ω low loss coaxial type.

Check the connections have not oxidised. Clean the

connectors with contact cleaner if they appear oxidised.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR280 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info