Bedienungsanleitung Arcam fmj t32 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Französisch)

161369

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

E-4

installation

Arcam’s T32 provides class-leading sound quality from a range of radio

sources: FM, AM, DAB and/or Sirius. (e range is market determined,

depending on the national availability of radio sources.) In addition, the

T32 works beautifully with Arcam’s rDock or rLead accessories, giving

your iPod® a rst class entry ticket into your home Hi-Fi system.

As part of an Arcam system, the high performance T32 tuner is

designed to truly bring your music to life.

Placing the unit

< Place the T32 on a level, rm surface, avoiding

direct sunlight and sources of heat or damp.

< Do not place the T32 on top of an amplier or

other source of heat.

< Do not place the T32 in an enclosed space such as

a bookcase or closed cabinet unless there is good

provision for ventilation. e T32 is designed to

run warm during normal operation.

< Do not place any other component or item on top

of the T32 as this may obstruct airow around the

unit, causing the T32 to run hot.

< Make sure the remote-control receiver

(behind the FMJ badge on the front panel) is

unobstructed, or remote control will be impaired.

< Do not place your record deck on top of this

unit. Record decks are very sensitive to the noise

generated by mains power supplies which will be

heard as a background ‘hum’ if the record deck is

too close.

Power

e T32 is supplied with a moulded mains plug already

tted to the lead. Check that the plug supplied ts your

supply – should you require a new mains lead, please

contact your Arcam dealer.

If your mains supply voltage or mains plug is dierent,

please contact your Arcam dealer immediately

Push the IEC plug end of the power cable into the socket

on the back of the T32, making sure that it is pushed in

rmly. Plug the other end of the cable into your mains

socket and, if necessary, switch the socket on.

Remote control input

e REMOTE IN input can be used to pass RC5 codes

to the T32 if it is installed in a position, or a system,

where infrared cannot be used. If this is required, please

contact your dealer for further information.

In normal use there is no need to make any connections

to this input.

e REMOTE IN input requires a mono 3.5mm jack,

with the tip active and the sleeve grounded.

e remote control signals must be in modulated

RC5 format (at 36kHz), with a voltage level of

between 5V and 12V.

Interconnect cables

We recommend the use of high-quality screened cables

that are designed for the particular application. Other

cables will have dierent impedance characteristics

that will degrade the performance of your system (for

example, do not use cabling intended for video use to

carry audio signals). All cables should be kept as short as

is practically possible.

It is good practice when connecting your equipment to

make sure that the mains power-supply cabling is kept

as far away as possible from your audio cables. Failure to

do so may result in unwanted noise in the audio signals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam fmj t32 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info