Bedienungsanleitung Arcam Logo (Seite 4 von 32) (Deutsch, Englisch, Holländisch, Französisch)

578804

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

E-4

Positioning the unit

< Place the Logo speaker unit on a level, ﬁrm

surface, avoiding direct sunlight and sources of

heat or damp.

< Do not place Logo in an enclosed space such

as a bookcase or closed cabinet unless there is

good provision for ventilation. The Logo speaker

unit is designed to run warm during normal

operation.

< Do not place your record deck on top of Logo.

Record decks are very sensitive to the noise

generated by mains power supplies which will

be heard as a background ‘hum’ if the record

deck is too close. Vibrations from Logo may also

cause the pickup stylus to jump tracks.

Power

Logo is supplied with a moulded mains plug already

ﬁtted to the lead. Check that the plug supplied ﬁts

your supply – should you require a new mains lead,

please contact your Arcam dealer. Logo is ﬁtted with

a transformer designed to accept nominal mains

voltages from 100V to 240V.

Push the IEC plug end of the power cable into the

socket on the back of Logo, making sure that it is

pushed in ﬁrmly. Plug the other end of the cable into

your mains socket and, if necessary, switch the socket

on.

Logo is ﬁtted with a main power switch on the rear

panel, above the power inlet: make sure that this is

switched on to use Logo.

If your Logo is not to be used for a prolonged period,

switch the unit off at the main power switch.

Indicator LED

An indicator LED is positioned across

the top edge of Logo’s cabinet.

When the indicator LED is off, it

indicates that the speaker is completely

disconnected from the mains. A blue

light from the indicator shows that the speaker is

powered up and ready for immediate use. A red

light from the indicator shows that the speaker is in

standby (power-saving) mode and will power up as

soon as an audio signal is received.

Standby switch

The push-in STANDBY switch provides two

settings:

AUTO and MANUAL.

‘

AUTO’ (button out) switches Logo’s

ampliﬁer to standby after a period of

idleness (about 15 minutes) when no audio signal has

been received. ‘

MANUAL’ (button in) means that Logo’s

ampliﬁer is on whenever the unit is receiving mains

power.

Interconnect cables

We recommend the use of high-quality screened

audio interconnect cables. Poor quality cables will

degrade the performance of your system. All cables

should be kept as short as is practically possible.

It is good practice when connecting your equipment

to make sure that the mains power-supply cabling is

kept as far away as possible from your audio cables.

Failure to do so may result in unwanted noise in the

audio signals.

installation

Connecting to a sound source

Check that your sound processor/receiver is switched

off before connecting Logo. Failure to do this may

result in both speaker and ampliﬁer damage.

If your sound source has a

PRE-OUT SUB or LFE OUT

output, connect this to

IN LFE on the back panel using

RCA (phono) connectors at each end. If your sound

source does not have a SUB or LFE output, connect

the left and right channels of the stereo pre-amp

output (

PRE OUT L and PRE OUT R) to IN L and IN R,

respectively.

You may connect both the

LFE and the L and R

outputs to Logo if you wish to use both the LFE

channel and to supplement the bass response of

‘Large’ Left and Right speakers.

OUT L, OUT R and OUT LFE provide line-level outputs

for ‘daisy-chaining’ further units, in a multi-room

installation, for example.

After connecting

Turn the sound source ampliﬁer volume down to

minimum before switching on. Switch the source

ampliﬁer on, select a source signal, then gradually

increase the volume to the required listening level.

Care of your speaker

Running-in

In the same way as a new car requires a ‘running-in’

period, so do all loudspeakers. Your Logo may sound

good when you ﬁrst connect it, but with time it will

improve dramatically. Expect about 50 hours use

before the full potential of your Logo is realised.

Cleaning

To clean your speaker simply use a soft, slightly

dampened cloth to wipe off any dust or dirt. Do not

use solvent-based or chemical cleaning products as

these may damage the ﬁnish of the speaker cabinet.

Power handling

Arcam speakers are designed to reproduce recorded

music under normal domestic conditions. We do

not recommend nor warrant them for commercial

applications, such as discothèques, public address, etc.

Note: When connecting Logo to signal leads,

or when moving Logo to a new position, make sure

that the unit is not receiving power by switching off

and disconnecting the power lead.

AUTO

MANUAL

STANDBY

LFE

ON OFF

OUT

LFE

100-240V~50/60HZ 275W MAX

FUSE: T2.5AL 250V

USE ONLY WITH A 250V FUS E

PHASE STANDBY

AUTO

MANUAL

0.3

0.5

0.7

0.9

1.1

1.3

1.5

X-OVER Q

VOLUME

100

115

125

140

160

X-OVER FREQ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam Logo Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info