Bedienungsanleitung Arcam P349 (Seite 12 von 107) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

578726

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

E-19E-18

English

ST/BRIDGE/DM

MODE

XLR/RCA

INPUT

25dB/31dB

GAIN

PRE

OUT

4–16 OHMS. CLASS 2 WIRING

SPEAKER 1 SPEAKER 2

4–16 OHMS. CLASS 2 WIRING

SPEAKER 2 SPEAKER 1

PRE IN R PRE IN L

110-120V/220-240V

~ 50-60 Hz

350W MAX

POWER INLET

SUPPLY

VOLTAGE

SWITCH POSITIONS

115 = 110 - 120V~

230 = 220 - 240V~

TRIGGER IN

TRIGGER OUT

PHONO

GROUND

ONLY

PHONO

(MM)

CD TUNER SAT BD PVR AV

RECORD

OUT

PRE

OUT

AUX R AUX L PRE OUT R PRE OUT L

TRIGGER OUT

6V 1A 12V 1.5A

ACCESSORY

POWER

110-120V/220-240V

~ 50-60 Hz

350W MAX

POWER INLET

SUPPLY

VOLTAGE

SWITCH POSITIONS

115 = 110 - 120V~

230 = 220 - 240V~

Dual mono - P49 only

Dual mono requires the use of a power amplier for

each channel.

We recommend that you use the SPEAKER 1 L set

of terminals on your P49 power amps for the low

frequencies and the SPEAKER 2 R set of terminals for the

high frequencies.

On one of the P49’s, connect the red positive speaker

terminal labelled SPEAKER 1 L+ to the positive LF terminal

of your right speaker. Similarly, connect the black

negative speaker terminal labelled SPEAKER 1 L to the

negative LF terminal of your right speaker. Repeat this

process for the le speaker, using the terminals labelled

SPEAKER 1 L+ and L on the other P49 power amp.

On the rst P49, connect the red positive speaker

terminal labelled SPEAKER 1 R+ to the positive HF

terminal of your right speaker. Similarly, connect the

black negative speaker terminal labelled SPEAKER 1 R to

the negative HF terminal of your speaker. Repeat this

process for the le speaker, using the terminals labelled

SPEAKER 1 R+ and R on the second P49.

In this setup only one interconnect is required to each

power amplifer and it should be connected to the

PRE IN L input. e interconnects can be either XLR

(recommended for longer cable runs) or phono (RCA).

Set the INPUT switch on the P49’s to the appropriate

setting for the cables used.

Note: PRE IN R has no function in this arrangement.

WARNING: the strip of metal on the speakers connecting

the low frequency (LF) terminals to the high frequency (HF)

terminals MUST BE REMOVED. Failure to do so will result

in damage to both ampliers, which will not normally be

covered under warranty.

To allow the power state of the P49 to be controlled by

the A49 please connect the TRIGGER OUT to the TRIGGER

IN using a mono 3.5mm jack lead – not supplied.

A C49 pre-amp and two P49 power amps in dual mono configuration.

ST/BRIDGE/DM

MODE

XLR/RCA

INPUT

25dB/31dB

GAIN

PRE

OUT

4–16 OHMS. CLASS 2 WIRING

SPEAKER 1 SPEAKER 2

4–16 OHMS. CLASS 2 WIRING

SPEAKER 2 SPEAKER 1

PRE IN R PRE IN L

110-120V/220-240V

~ 50-60 Hz

350W MAX

POWER INLET

SUPPLY

VOLTAGE

SWITCH POSITIONS

115 = 110 - 120V~

230 = 220 - 240V~

TRIGGER IN

TRIGGER OUT

C49

P49 P49

Remove

metal strip

Remove

metal strip

Make sure MODE

switch is set to DM

on both amps

Make sure INPUT

switch matches wired

configuration (XLR or RCA)

on both amps

ST/BRIDGE/DM

MODE

ST/BRIDGE/DM

MODE

ST/BRIDGE/DM

MODE

XLR/RCA

INPUT

XLR/RCA

INPUT

25dB/31dB

GAIN

25dB/31dB

GAIN

NOTE: Units can be interconnected via XLR or RCA.

Both versions shown for illustration purposes only.

Make sure GAIN

switch is set to 31dB

on both amps

ST/BRIDGE/DM

MODE

ST/BRIDGE/DM

MODE

ST/BRIDGE/DM

MODE

XLR/RCA

INPUT

XLR/RCA

INPUT

25dB/31dB

GAIN

25dB/31dB

GAIN

ST/BRIDGE/DM

MODE

ST/BRIDGE/DM

MODE

ST/BRIDGE/DM

MODE

XLR/RCA

INPUT

XLR/RCA

INPUT

25dB/31dB

GAIN

25dB/31dB

GAIN

troubleshooting

Sound cuts-out unexpectedly

If the temperature of the internal heatsink rises above

a safe level, then a thermal cut-out inside the amplier

operates to protect the unit and the protection system

temporarily removes power to the speakers. e system

will reset itself as the heatsink cools down.

< With two pairs of low-impedance speakers

connected (6Ω or less), overloads are more likely.

Overloading the amplier may cause it to shut

down because of overheating.

< Note that, due to the high output voltage from

some CD players, it is possible to drive your

amplier at full power even though the volume is

not set at maximum.

If you are having trouble with your amplier, check the

following items.

No sound

Check the following:

< e amplier is switched on.

< e A49/C49 is not muted (i.e. MT (mute) is not

shown on the display panel; the power LED is

showing green, not orange or red).

< e selected source going in to the A49/C49 is

generating audio (e.g., if CD is selected, then the

CD is playing).

< e speaker outputs on the A49/P49/P349 are

active and the appropriate speaker LED is showing

green.

No remote control

Check the following:

< Check the remote control with fresh batteries.

< Ensure that the amplier and remote are both set to

the same control code - see page17.

< If the volume does not operate for a selected input,

check that processor mode has not been selected for

that input - see page12.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam P349 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info