Bedienungsanleitung Arctic Spas Mustang (Seite 88 von 124) (Englisch)

765011

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

• Screw the Spa Boy Housing Plug provided with your spa into the front of the Spa Boy Sensor Housing. This

will seal the water that is in the Housing and prevent the water in the Housing from draining when you drain

your spas water.

Warning: The Spa Boy Sensor must never be permitted to freeze and must always remain in contact with

water. If the Sensor freezes or is not left in contact with water at all times the sensor will fail and will require

replacement! Such failures are not covered by warranty.

What do we do when winterizing a Spa?

• You can now drain your spas water.

• Clean the Spa shell with a mixture of water and white vinegar. Rinse the shell down with fresh water and then

polish the shell with Arctic Pure, Reection.

• When relling your spa with water, leave the Spa Boy Sensor Plug secured in place until the water line is

higher than the Spa Boy Housing.

• The Spa Boy Housing Plug can now be unscrewed from the Housing and the Housing Grate can be screwed

back into the Housing.

• Once the water level has been reached the bottom of the pillow line you can turn the breaker back on to re-

power your spa.

Question 4 Does adding salt to the spas water impact pH? Yes adding salt to the spas water will increase

the pH level. The chlorine that is produced by a salt chlorinator plays a role in the water chemistry of a salt spa.

Salt is sodium chloride. When an electric charge is passed through salt water, the sodium chloride is turned

into sodium hypochlorite. This is the same kind of chlorine that is sold by the gallon as liquid chlorine. The most

important feature of sodium hypochlorite is a high pH. When the salt chlorinator produces chlorine, it raises the

pH of the spas water. Strive to achieve a Low pH level 7.2. pH must not exceed 7.6.

Question 5 What do I do if my ORP Reading is below the Optimum Range? If Spa Boy reects that the

ORP is below the Optimum Range of 545 – 550 mV you must rst consider that water chemistry may have

been a󰀨ected by recent bather load and spa usage, at times the ORP value will overshoot or undershoot the

Optimum Range. If the Spa Boy Dashboard on My Arctic Spa reects that the ORP is below 545 mV do the fol-

lowing:

• Check Spa Boy Dashboard through My Arctic Spa to see if the Dashboard reects sanitizing YES, if yes Spa

Boy is currently producing sanitizer. Re-check ORP in a few hours to conrm ORP is increasing.

• If Dashboard reects Sanitizing NO: Trip the spas breaker to isolate the power to the spa and then turn the

breaker back on to repower the spa. Check Spa Boy Dashboard through My Arctic Spa to see if the Dashboard

reects sanitizing YES, if yes Spa Boy is currently producing sanitizer. Re-check ORP in a few hours to conrm

ORP is increasing.

• If Dashboard reects Sanitizing NO: First, try pressing the Spa Boy BOOST button on the Arctic Spas App or

myarcticspa.com dashboard under “Settings/Spa Boy Status” to manually activate the Spa Boy system for 30

minutes.

Understanding Spa Boy®

Owners Manual - Spa Boy®

8888

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arctic Spas Mustang Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info