Bedienungsanleitung Argo DRY PURY EVO 11-13 (Seite 6 von 17) (Englisch)

805017

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

24V 04/23

APPLIANCE START-UP

Place the product on a at and stable heat-resistant surface, at least 1 metre away from ammable or heat-sensitive

materials and 50 cm away from walls or other obstructions.

Make sure the water tank is in the correct position.

Connect the power cord to a suitable electric socket (220-240V~).

Turn the appliance on with POWER on the control panel. The unit emits a sound signal and is in standby, the colored

LED on the front panel lights up. The display shows the humidity% detected in the room, therefore set a humidity % lower

than at least 3% compared to that in the room to make the dehumidier work.

The dehumidier is designed to operate at ambient temperatures from + 5°C to + 35°C.

If it is operated at low temperatures, ice may form on the evaporator, degrading its operation.

When this happens, the dehumidier goes into defrost mode. The compressor stops, but the fan continues running.

The defrosting operation may start up and operate for some minutes; during the defrosting operation, the dehumidication

function may intermit: please don’t turn off the switch or pull out the power plug of the dehumidier.

We recommend not using the dehumidier in room temperatures lower than 5°C.

Do not remove the tank when the unit is in operation.

If you wish to make continuous draining of condensate, follow the instructions in the dedicated paragraph.

OPERATING PRECAUTIONS

The dehumidier starts only if the humidity level in the room is higher than 3% the set one.

The dehumidier will continue to operate until the set humidity level is reached, except for any interruptions due to

lling the tank.

When the water tank is full, the compressor stops running immediately and dehumidication stops; the fan stops after

3 minutes. Empty the tank and reposition it: after carrying out these operations, the unit will start operating again.

ATTENTION:

After each interruption of operation, at least 3 minutes must elapse before the dehumidier restarts: this startup delay

protects the compressor from damage.

If, on the other hand, the humidity% set is higher than that present in the room, the dehumidier will not start.

If, after following the instructions for starting the dehumidier, the dehumidier does not start and the (POWER) symbol

does not light up, or the dehumidier stops without reason, check that the condition of the plug and the power cord

are good. Once this is done, wait 10 minutes and then restart the dehumidier.

If, even after 10 minutes, the dehumidier does not start, or if the cable or the plug are damaged, switch off the

dehumidier and contact a technical assistance center.

WARNING:

When the dehumidier is running, the compressor produces heat and the appliance emits warm air into the room.

The room temperature will therefore tend to increase. This is completely normal.

SWITCHING OFF THE DEHUMIDIFIER

To turn the dehumidier off press the POWER button. This shuts off power to the unit.

Unplug the appliance if you do not intend to use it for some time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo DRY PURY EVO 11-13 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo DRY PURY EVO 11-13

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info