Bedienungsanleitung Argo DRY PURY EVO WF 17-21 (Seite 15 von 18) (Englisch)

805014

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

34V 04/23

manufacturer’s technical department for assistance.

The following checks shall be applied to installations using ammable refrigerants:

• The actual refrigerant charge is in accordance with the room size within which the refrigerant containing parts

are installed;

• The ventilation machinery and outlets are operating adequately and are not obstructed;

• lf an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence of

refrigerant;

• Marking to the equipment continues to be visible and legible. Markings and signs that are illegible shall be

corrected;

• Refrigeration pipe or components are installed in a position where they are unlikely to be exposed to any

substance which may corrode refrigerant containing components, unless the components are constructed of

materials which are inherently resistant to being corroded or are suitably protected against being so corroded.

• Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks and component inspection

procedures. lf a fault exists that could compromise safety, then no electrical supply shall be connected to the

circuit until it is satisfactorily dealt with. lf the fault cannot be corrected immediately but it is necessary to continue

operation, an adequate temporary solution shall be used. This shall be reported to the owner of the equipment

so all parties are advised.

lnitial safety checks shall include:

• That capacitors are discharged: this shall be done in a safe manner to avoid possibility of sparking;

• That no live electrical components and wiring are exposed while charging, recovering or purging the system;

• That there is continuity of earth bonding.

• Repairs to sealed components

During repairs to sealed components, all electrical supplies shall be disconnected from the equipment being

worked upon prior to any removal of sealed covers, etc. lf it is absolutely necessary to have an electrical supply

to equipment during servicing, then a permanently operating form of leak detection shall be located at the most

critical point to warn of a potentially hazardous situation. Particular attention shall be paid to the following to

ensure that by working on electrical components, the casing is not altered in such a way that the level of protection

is affected. This shall include damage to cables, excessive number of connections, terminals not made to originai

specication, damage to seals, incorrect tting of glands, etc.

• Ensure that the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded to the point that they no longer serve the purpose

of preventing the ingress of ammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s specications.

NOTE: the use of silicon sealant can inhibit the effectiveness of some types of leak detection equipment. lntrinsically

safe components do not have to be isolated prior to working on them.

• Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this will not exceed

the permissible voltage and current permitted for the equipment in use. lntrinsically safe components are the only

types that can be worked on while live in the presence of a ammable atmosphere. The test apparatus shall beat

the correct rating. Replace components only with parts specied by the manufacturer. Other parts may result in the

ignition of refrigerant in the atmosphere from a leak.

• Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any other

adverse environmental effects. The check shall also take into account the effects of aging or continual vibration

from sources such as compressors or fans.

• Detection of ammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of refrigerant

leaks. A halide torch (or any other detector using a naked ame) shall not be used.

• Leak detection methods

The following leak detection methods are deemed acceptable for all refrigerant systems. Electronic leak detectors

may be used to detect refrigerant leaks but, in the case of ammable refrigerants, the sensitivity may not be

adequate, or may need re-calibration. (Detection equipment shall be calibrated in a refrigerant-free area.) Ensure

that the detector is not a potential source of ignition and is suitable for the refrigerant used. Leak detection

equipment shall be set at a percentage of the LFL of the refrigerant and shall be calibrated to the refrigerant

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo DRY PURY EVO WF 17-21 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo DRY PURY EVO WF 17-21

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info