Bedienungsanleitung Argo Emix Tank (Seite 27 von 30) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Finnisch)

665483

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

To enter the conguration menu, with Emix already on, press and hold the BUTTON 9 for about 7 seconds.

When only the RED LED lights up, keep BUTTON 9 pressed until the BLUE LED lights up. At this point release BUTTON 9.

After 5 seconds without any operation, Emix exits the conguration procedure and returns to the previous menu.

Booster mode setting

The use of electrical heating elements installed in a storage tank or in a electrical water heater allows you to heat the cold

water faster, to reach the desired water temperature even in conditions of very low external temperatures or to heat the

water even if the heat pump is switched off for maintenance.

When you activate the Booster mode, the software will automatically handle the electrical heaters.

If after 120‘ from start up of the system (the time counter starts when the Booster mode is set), the water setpoint is not

reached, the rst electrical element is automatically activated. The other elements, one by one, will be activated every

120‘ following the course of the water temperature, until reaching the setpoint.

To activate / deactivate the Booster mode, from the conguration menu, quickly press BUTTON 9 until the only BLUE

LED is ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.

3 consecutive beeps conrm the setting.

NOTE

By default, the Booster mode is off.

Super Booster mode setting

When the Super Booster mode is activated, all the connected electrical heaters will be activated at the same time, to-

gether with the heat pump.

When the setpoint is reached, all electrical heaters are switched off and the Super Booster mode is automatically turned

off.

To activate / deactivate the Super Booster mode, from the conguration menu, quickly press BUTTON 9 until the only

RED LED is ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.

3 consecutive beeps conrm the setting.

NOTE

By default, the Super Booster mode is off.

EMIX CONFIGURATION

Setpoint limit setting with Heat Pump

It is possible to set the maximum achievable setpoint when the Heat Pump is working only for Emix. This limit can be set

to 50°C or 58°C.

To change the setting, from the conguration menu, quickly press BUTTON 9 until the BLUE and YELLOW LEDs are

ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.

3 consecutive beeps conrm the setting.

NOTE

By default the limit is set to 50°C. We recommend to keep this setting to preserve the Emix performance.

Antilegionella cycle setting

To activate / deactivate the Antilegionella cycle, from the conguration menu, quickly press BUTTON 9 until the only YEL-

LOW LED is ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.

3 consecutive beeps conrm the setting.

NOTE

By default, the Antilegionella cycle is on. It is highly recommended to keep it enabled.

For details on the operation of the Antilegionella cycle, see section “ANTILEGIONELLA CYCLE”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Emix Tank Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Emix Tank

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info