Bedienungsanleitung Argo Emix (Seite 28 von 30) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Finnisch)

665482

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Temperature delta setting for restart of the heat pump

When the water temperature reaches the set value or the maximum achievable value (in the case of Emix operation with-

out other indoor units), the heat pump switches off and starts up again only when the water temperature drops below the

desired temperature of a certain value (delta).

You can change the startup delta of the heat pump by setting it to 5°C or 10°C.

To change the set value, from the conguration menu, quickly press BUTTON 9 until the BLUE and RED LEDs are ash-

ing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.

3 consecutive beeps conrm the setting.

NOTE

By default the startup delta of the heat pump is set to 10°C.

Reset of the factory settings

To reset all the factory settings, from the conguration menu, quickly press BUTTON 9 until the BLUE, YELLOW and RED

LEDs are ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.

3 consecutive beeps conrm the reset of factory settings.

In addition to the already described modes in the section “EMIX CONFIGURATION”, Emix software can automatically

manage electrical back up heaters under certain conditions. This mean that these operation modes are not to be set and

that can not be deactivated. They are:

- Antifreeze mode

- Cold draft prevention mode

- Electrical water heater mode (in case heat pump is not active)

- Antilegionella cycle

Electrical back up heater management – Antifreeze mode

If water temperature inside the tank is lower than 5° C, all connected electrical elements are switched on until the water

temperature reaches 10° C.

Electrical back up heater management – Cold draft prevention mode

When one or more indoor units are in cold draft prevention mode and compressor is operating since 20’, one by one

electrical element are switched on every 20’; they will be switched off one by one when no indoor unit will be any more

in Cold draft prevention mode.

Electrical back up heater management – Electric water heater mode

If the outdoor unit is stopped for maintenance the end user could decide to use Emix as controller of the electrical heater

elements located inside the tank, exactly like any electrical water heater. In this case, if the water temperature is lower

than the desired temperature for more than 10’, all the connected electrical heaters will switch on up to the reaching of

the setpoint. End users can switch off Emix if they do not want to utilise this option.

Electrical back up heater management – Antilegionella cycle

During the Antilegionella cycle, one or more electrical heaters may be automatically switched on. See section “ANTILE-

GIONELLA CYCLE”.

OPERATION OF THE ELECTRICAL HEATER ELEMENTS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Emix Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Emix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info