Bedienungsanleitung Argo Future (Seite 15 von 22) (Englisch)

805029

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

V 12/21 36

In cooling mode, the temperature increases by 1 °C in an hour then by 2 °C in two hours, and remains in this setting

for the whole period. The Sleep function is not available in the ventilation, dehumidification and auto modes. The

indicator light turns on display of remote control whenever the Sleep function is set.

(6) TIMER BUTTON (on both the remote control and portable unit)

Press and hold this button for 1 second to set the timer.

1）Timer-on (automatic switch-on)

When the appliance is off, this button is used to set a delay after which the unit will switch on.

Remote control: Press TIMER. The T-ON and H icons will light up on the remote control. Press the + and - buttons

within 5 seconds to set the delay. The T-ON icon will remain on to indicate that the TIMER has been set.

Portable unit: Press TIMER. Select a number of hours from 0.5 to 24. Press the TIMER button to confirm.

2）Timer-off (automatic switch-off)

When the appliance is running in the COOL mode, set a delay after which the unit will switch off.

Remote control: Press TIMER. The T-OFF and H icons will light up. Press the + and - buttons within 5 seconds to

set the delay. Select a number of hours from 0.5 to 24. Press the TIMER button to confirm. The T-OFF icon will

remain lit to indicate that the switch-off TIMER is running.

Portable unit: Press TIMER. Select a number of hours from 0.5 to 24. Press the TIMER button to confirm.

Resetting the timer: If a TIMER has been set, press TIMER to display the delay. Press TIMER again to cancel the

setting.

(8) TEMPERATURE AND ERROR DISPLAY

Problem Cause Solution

H8 Tank full of water. Empty the tank.

If the problem persists, contact a service centre.

F1 Room temperature sensor failure. Contact a service centre.

F2 Failure of temperature sensor on the

evaporator.

Contact a service centre.

F0 Refrigerant leakage. Air conditioner

out of order.

Contact a service centre.

H3 Overload protection device on

compressor.

The room temperature exceeds the appliance's operating

range (beyond 35°) or there is too much humidity. Wait for

the temperature to drop below 35 °C.

Check if the evaporator and compressor are obstructed by

objects. If they are, remove the objects, disconnect the unit

then restore the power supply.

Clear the obstructed ventilation grilles.

If the problem persists, contact a service centre.

E8 Overload protection.

F4 The external temperature sensor has

short-circuited.

Contact the service centre.

The temperature and error display lights up only in the COOL mode. In the DRY and FAN modes the display does not light

up.

SAFETY FUNCTIONS

REMOTE CONTROL LOCK

Simultaneously press "+" and "-" to lock the remote control.

The "Lock" icon will light up on the remote control, and the latter will not respond to commands.

SWITCHING BETWEEN °C AND °F.

Press the "-" and "MODE" buttons simultaneously to switch between °C and °F.

LIGHT FUNCTION

Press the “+” and “FAN” buttons simultaneously for 3 seconds to set the activation/ deactivation of the lamp.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Future Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Future

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info