Bedienungsanleitung Argo Future (Seite 19 von 22) (Englisch)

805029

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

V 12/21 40

---Refrigeration pipe or components are installed in a position where they are unlikely to be exposed to any substance

which may corrode refrigerant containing components, unless the components are constructed of materials which

are inherently resistant to being corroded or are suitably protected against being so corroded.

 Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks and component inspection

procedures. lf a fault exists that could compromise safety, then no electrical supply shall be connected to the circuit

until it is satisfactorily dealt with. lf the fault cannot be corrected immediately but it is necessary to continue operation,

an adequate temporary solution shall be used. This shall be reported to the owner of the equipment so all parties are

advised.

lnitial safety checks shall include:

---That capacitors are discharged: this shall be done in a safe manner to avoid possibility of sparking;

---That no live electrical components and wiring are exposed while charging, recovering or purging the system;

---That there is continuity of earth bonding.

 Repairs to sealed components

During repairs to sealed components, all electrical supplies shall be disconnected from the equipment being worked

upon prior to any removal of sealed covers, etc. lf it is absolutely necessary to have an electrical supply to equipment

during servicing, then a permanently operating form of leak detection shall be located at the most critical point to

warn of a potentially hazardous situation.

Particular attention shall be paid to the following to ensure that by working on electrical components, the casing is

not altered in such a way that the level of protection is affected. This shall include damage to cables, excessive

number of connections, terminals not made to originai specification, damage to seals, incorrect fitting of glands, etc.

• Ensure that the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded to the point that they no longer serve the purpose

of preventing the ingress of flammable atmospheres. Replacement parts shall be in accordance with the

manufacturer's specifications.

NOTE: The use of silicon sealant can inhibit the effectiveness of some types of leak detection equipment. lntrinsically

safe components do not have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this will not exceed

the permissible voltage and current permitted for the equipment in use.

lntrinsically safe components are the only types that can be worked on while live in the presence of a flammable

atmosphere. The test apparatus shall beat the correct rating.

Replace components only with parts specified by the manufacturer. Other parts may result in the ignition of refrigerant

in the atmosphere from a leak.

Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any other

adverse environmental effects. The check shall also take into account the effects of aging or continual vibration from

sources such as compressors or fans.

Detection of flammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of refrigerant

leaks. A halide torch (or any other detector using a naked flame) shall not be used.

Leak detection methods

The following leak detection methods are deemed acceptable for all refrigerant systems.

Electronic leak detectors may be used to detect refrigerant leaks but, in the case of flammable refrigerants, the

sensitivity may not be adequate, or may need re-calibration.

(Detection equipment shall be calibrated in a refrigerant-free area.) Ensure that the detector is not a potential source

of ignition and is suitable for the refrigerant used.

Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be calibrated to the

refrigerant employed, and the appropriate percentage of gas (25 % maximum) is confirmed.

Leak detection fluids are suitable for use with most refrigerants but the use of detergents containing chiarine shall be

avoided as the chiarine may react with the refrigerant and corrode the copper pipe-work. If a leak is suspected, all

naked flames shall be removed/extinguished.

If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered from the system,

or isolated (by means of shut off valves) in a part of the system remote from the leak. For appliances containing

flammable refrigerants, oxygen free nitrogen (OFN) shall then be purged through the system both before and during

the brazing process.

Removal and evacuation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Future Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Future

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info