Bedienungsanleitung Argo Greenstyle Plus (Seite 17 von 30) (Englisch)

805092

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

48V 11/22

TABLE A - Minimum room area (m2)

Maintenance notes

• Check whether the maintenance area or the room area meet the requirement of “table a” the unit is only allowed

to be operated in rooms that meet these requirements.

• Check whether the maintenance area is well-ventilated. The continuous ventilation status should be kept during the

entire operation process.

• Check whether there is a re source or potential re source in the maintenance area. Running re is prohibited in

the maintenance area and the “no smoking” sign should be hanged.

• Check whether the warning sign is in good condition, otherwise replace it.

Welding

• If it is necessary to cut or weld the refrigerant system pipes in the maintenance procedures, please follow the steps

here below:

• Shut down the unit and cut power supply

• Eliminate the refrigerant

• Vacuum with a vacuum machine

• Clean the pipes with the N2 gas

• Cut and weld or

• Bring the unit to a service centre for welding

• The refrigerant should be recycled in a specialized storage tank.

• Make sure there aren’t any free ames near the outlet of the vacuum pump and that it’s well-ventilated.

Filling the refrigerator circuit

• Use refrigerant lling appliances specialized for R32. Make sure that different kinds of refrigerant don’t contaminate

one another.

• The refrigerant tank should be kept upright when lling with the refrigerant.

• Stick the label on the system after lling is nished.

• Don’t overll.

• After lling is nished, please test the unit for leakage detection before the operation test; another test for leakage

detection should be carried out when the refrigerant is removed.

Safety instructions for transportation and storage

• Please use a ammable gas detector to check before unloading and opening the container.

• No re source and no-smoking.

• According to the local rules and laws.

• Before installating, please contact with local authorized maintenance center, if unit is not installed by the authorized

maintenance center, the malfunction may not solved due to discommodious contact.

• The air conditioner must be installed by professionals according to the national wiring rules and this manual.

• Refrigerant leak test must be made after installation.

• To move and install air conditioner to another place, please contact our local special service center.

SAFETY PRINCIPLES FOR INSTALLATION

• Fire prevention device shall be prepared before installation.

• Keep installing site ventilated (open the door and window)

• Ignition source, re, smoking and mobile phones are not allowed to exist in area where R32 refrigerant located.

CAUTION

Minimum room

area (m2)

Charge amount (kg) ≤1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5

Floor location / 14.5 16.6 19.3 22 24.8 27.8 31 34.3 37.8 41.5 45.4 49.4 53.6

Window mounted / 5.2 6.1 7 7.9 8.9 10 11.2 12.4 13.6 15 16.3 17.8 19.3

Wall mounted / 1.6 1.9 2.1 2.4 2.8 3.1 3.4 3.8 4.2 4.6 5 5.5 6

Ceiling mounted / 1.1 1.3 1.4 1.6 1.8 2.1 2.3 2.6 2.8 3.1 3.4 3.7 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Greenstyle Plus Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Greenstyle Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info