Bedienungsanleitung Argo Hi-comfort Plus (Seite 19 von 30) (Englisch)

805094

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

50V 11/22

• The minimum clearance between the air conditioner and the combustibles is 1.5 m.

• The interconnection cord connect the indoor and outdoor units. You must rst choose the right cable size before

preparing it for connection.

• Cable Types:

• Outdoor Power Cable: H07RN-F or H05RN-F;

• Interconnection cord: H07RN-F or H05RN-F;

• Minimum Cross-Sectional Area of Power cable and interconnection

cord:

• The size of the interconnection cord, power cable, fuse, and

switch needed is determined by the maximum current of the unit.

The maximum current is indicated on the nameplate located on the

side panel of the unit. Refer to this nameplate to choose the right

cable, fuse, or switch.

• Note: core number of cable refer to the detailed wiring diagram

adhered on the unit which you purchased.

INSTALLATION WARNINGS

• WARNING: Make sure that the power supply is disconnected before carrying out any work on the unit.

• WARNING: Wear appropriate personal protective equipment before carrying out any work on the unit.

• WARNING: The appliance must be reinstalled in accordance with national system regulations.

• WARNING: Wiring and installation must only be performed by a qualied technician trained to install, modify,n

extend and service the unit and perform safety and functionality tests.

• WARNING: Install a device, master switch or electric plug that will allow all the power from the appliance to be

switched off.

• The following information is essential for correct unit installation. However, the installer should use his or her

experience to install the unit according to specic requirements.

• Do not install the unit in locations where there are ammable gases or acid or alkaline substances that may

irreparably damage the copper-aluminium heat exchangers or internal plastic components.

• Do not install the unit in ofces or kitchens where oil vapours mixed with treated air may settle on the exchange

coils, reducing performance, or on the unit’s internal parts, damaging the plastic components.

• ATTENTION: For the connection between the units, use only annealed and deoxidized copper pipe for

conditioning and refrigeration and insulated with expanded polyethylene of min. 8 mm.

ELECTRICAL CONNECTION REQUIREMENTS

• Electrical safety standards must be met when installing the unit.

• Use a power supply circuit and circuit breaker that comply with local safety regulations.

• Make sure that the power supply matches the requirements of the air conditioner. An unstable power supply or

incorrect wiring may result in a fault. Install suitable power cables before switching on the air conditioner.

• Correctly connect the live, neutral and earth wires to the power outlet.

• Disconnect the power supply before carrying out any work on the electrical circuit or carrying out any safety work.

For models with a plug, make sure the plug is easily accessible after installation.

• Do not connect the power before installation is complete.

• Do not use the appliance if the power cable or plug are damaged. If the power cable is damaged it must be

replaced by the manufacturer, retailer or other qualied person to avoid a hazard.

• Since the temperature of the cooling circuit is high, keep the interconnecting cable away from the copper pipe.

• The unit must be installed in accordance with national wiring regulations.

• Installation must only be performed by trained individuals in accordance with regulations.

The unit is charged with a slightly inammable refrigerant, R32. Improper handling of this gas may

expose people and materials to serious damage. More details on this refrigerant are given at the

beginning of this manual.

REQUIREMENTS FOR OPERATIONS AT HEIGHT

• When carrying out installation at 2 m or higher above the base level, safety belts must be worn and ropes of

Rated current of

appliance (A) Nominal corss-

sectional area (mm2)

> 3 e ≤ 6 0.75

> 6 e ≤ 10 1

> 10 e ≤ 16 1.5

> 16 e ≤ 25 2.5

> 25 e ≤ 32 4

> 32 e ≤ 40 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Hi-comfort Plus Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Hi-comfort Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info