Bedienungsanleitung Argo Hi-comfort Plus (Seite 27 von 30) (Englisch)

805094

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

58V 11/22

Here are warnings and safety instructions for the maintenance of systems containing ammable refrigerant (repairs

should only be carried out by specialists).

1. Any person involved in the work or in the interruption of a refrigeration circuit must be equipped with PEF (European

Refrigerators License) as required by the D.P.R. n.146/2018 implementing Regulation (EU) no. 517/2014.

2. Maintenance should only be performed as recommended by the equipment manufacturer. Maintenance and

repairs that require the assistance of other qualied personnel must be performed under the supervision of the

person competent in the use of ammable refrigerants.

Before starting work on systems containing ammable refrigerants, safety checks are required to ensure that the risk of

ignition is minimized.

1. Checks to be carried out on systems that use ammable refrigerants:

• the charge must be proportionate to the size of the room in which the units containing refrigerant are installed;

• units and ventilation openings must function properly and are not obstructed;

• if an indirect refrigerant circuit is used, the secondary circuit must be checked for the presence of refrigerant;

• the marking on the equipment must be visible and indelible. Illegible markings and signs must be corrected;

• refrigerant piping or components must be installed in a location where they are unlikely to be exposed to any

substance that can corrode the component-containing refrigerant, unless the components are constructed from

materials that are inherently resistant to corrosion or are adequately protected against corrosion.

2. Checks on electrical devices. Repair and maintenance of electrical components must include initial safety checks

and component inspection procedures. If there is a fault that could compromise safety, do not connect the power

supply to the circuit until it is satisfactorily resolved. If the fault cannot be remedied immediately, but operation must

continue, a suitable interim solution must be used. This must be reported to the owner of the equipment so that all

parties are informed.

Initial security checks include:

• Check that the capacitors are discharged: this must be done safely to avoid the risk of sparks;

• Verify that no electrical components and wiring are exposed while charging, restoring or draining the system;

• Check that there is ground continuity.

3. Check for refrigerant leaks. The area should be checked with an appropriate refrigerant detector before and

during work, to ensure that the technician is aware of potentially toxic or ammable atmospheres. Make sure that

the leak detection equipment in use is suitable for use with all applicable refrigerants, i.e. non-sparking, properly

sealed or intrinsically safe.

Check for R32 refrigerant leaks. Note: check for refrigerant leakage in an environment where there are no

potential sources of ignition. No halogen probe (or any other detector that uses an open ame) should be used.

Leak Detection Method: For systems with R32 refrigerant, an electronic leak detection tool is available to detect

and leak detection should not be conducted in a refrigerant environment. Make sure the leak detector does not

become a potential source of ignition and is applicable to the measured refrigerant. The leak detector must be set

for the minimum ammable fuel concentration (percentage) of the refrigerant. Calibrate and adjust to the correct

gas concentration (no more than 25%) with the refrigerant used. The uid used in leak detection is applicable to

most refrigerants. But do not use chloride based solvents to prevent the reaction between chlorine and refrigerants

and corrosion of copper piping. If you suspect a leak, remove all re from the scene or put out the re. If the

location of the leak is to be welded, then all refrigerants must be recovered or isolate all refrigerants away from

the leak site (using the shut-off valve). Before and during soldering, use OFN to purify the entire system.

4. Presence of re extinguisher. If hot work is to be performed on the refrigeration equipment or any associated part,

adequate re ghting equipment must be available. It is necessary to have a dry powder or CO2 extinguisher

adjacent to the charging area.

5. Ventilated area. Make sure the area is outdoors or is adequately ventilated before breaking into the system or

performing any hot work. Continuous ventilation must be present during the period in which the work is being

carried out. Ventilation should safely disperse the released refrigerant and preferably expel it to the atmosphere.

6. Controls on refrigeration equipment. When replacing electrical components, they must be t for purpose and with

WARNINGS FOR THE REFRIGERATION SYSTEM SPECIALIST

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Hi-comfort Plus Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Hi-comfort Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info