Bedienungsanleitung Argo Maxime Plus EU (Seite 16 von 41) (Englisch)

805050

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

V 12/21 57

(4) FAN SPEED ADJUSTMENT BUTTON (on control panel and on remote control)

On control panel, touch this button when the appliance is switched on for adjusting the ventilation accordingly the following

sequence:

On remote control, press this button to adjust the fan speed in the following sequence:

Auto (automatic ventilation) -> Low speed (low ventilation speed) -> Medium speed (medium ventilation speed) -> High

speed (high ventilation speed) -> Auto

Fan speed cannot be adjusted in DRY mode and is fixed at low.

When Auto fan speed is selected, the unit automatically adjusts the fan speed according to the factory settings.

In Dry mode the fan speed is fixed at low speed.

X-FAN function: Press and hold the fan speed button (FAN) for 2 seconds in COOL (cooling) or DRY (dehumidification)

mode, the icon appears and the fan continues to run for a few minutes to dry the inside of the unit, even if the power

has been turned off. When the unit is turned on, the X-FAN mode is not active. This function is not available in AUTO, FAN

and HEAT modes.

This function is used to dry the condensation that forms inside the appliance after it has been turned off, thus avoiding the

formation of mold.

After setting the X-FAN function, turn off the device with the ON / OFF button, the internal fan continues to operate for a

few minutes at low ventilation speed, if you want to stop the fan, keep the SPEED button pressed for 2 seconds.

(5) WIFI BUTTON (on control panel and on remote control)

On control panel touch this button to turn on/off the WiFi function. When the WiFi is on the LED is lighted on.

To reset WiFi settings hold this button for 10 seconds.

On the remote control, press the Wifi button to activate or deactivate the Wifi function, the corresponding icon on the

display will appear.

When the unit is off, press and hold the MODE and Wifi buttons simultaneously for 1 second to reset the Wifi to the factory

settings.

(6) SWING BUTTON (on control panel and on remote control)

On control panel touch this button to swing the flap automatically up & down, and when you have selected the desired

angle, press again to lock them in the desired angle.

On remote control press this button to swing the flap up & down, accordingly the following sequence:

When the SWING button is selected, the symbol appears on the remote control display and the flap swings in the

following sequence:

(7) TEMPERATURE AND ERROR DISPLAY ON CONTROL PANEL

With the exception of message H8, tank full, when an error occurs do not try to repair the air conditioner, always take it to

an Argoclima Service Center, otherwise the guarantee will no longer be valid.

Problem Cause Solution

H8 Tank full of water. Empty the tank.

If the problem persists, contact a service centre.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Maxime Plus EU Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Maxime Plus EU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info