Bedienungsanleitung Argo Nikko (Seite 9 von 21) (Englisch)

805067

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

31V 05/23

HOW TO USE THE APPLIANCE

OPERATING MODES

This appliance can be used for Cooling, Dehumidication and Ventilation. Before using the appliance, leave it in an

upright position for at least two hours.

Plug the power cord into an appropriate power outlet (220-240~V). Insert the batteries into the remote controller,

observing the polarities. Select the desired operating mode from the remote controller.

The air conditioner is equipped with a protection system which causes the unit to activate in Cooling and Dehumidication

mode only after an interval of approximately 3 minutes from the selection. Even when passing from one mode to

another, the fan continues to operate, but the compressor stops to restart after 3 minutes. This start delay protects the

compressor from overload.

THE DRAINAGE TUBE MUST BE CONNECTED to the appliance AT ALL TIMES: the only exception is when the

appliance is used in dehumidication mode only, in which case the appliance should be left to discharge directly

into the room for maximum efciency (see the “Dehumidication Mode” paragraph).

Periodically clean the easily removable air lter located on the side of the product to keep the air conditioning efcient.

1. COOLING MODE (COOL)

• Press the MODE button to select Cooling. The LED on the control panel lights up.

• The temperature adjustment range goes from 16 °C to 32 °C with 1 °C steps.

• In this mode, every time the unit is switched off by pressing the POWER button the appliance stores the set

temperature and when it is switched on again it will keep the setting.

• In cooling mode, the fan speed is high by default.

• In this mode it is possible to adjust the ventilation speed (Speed), set the Timer and activate the Sleep function

by holding down the Speed button for 3 seconds.

• For quieter operation, reduce speed to low.

2. DEHUMIDIFICATION MODE (DRY)

• Press the MODE button to select the Dehumidication mode. The LED on the control panel lights up.

• The temperature is controlled by the electronic board and cannot be adjusted.

• In this mode, each time the POWER button is pressed the unit switches off, the appliance saves the settings

and retains them when it is switched on again.

• The humidity % adjustment range is 35-80%, in dehumidication mode it is however not possible to adjust

the humidity %.

• The fan speed cannot be adjusted.

NOTE: the air conditioner does not cool the room when operating as a dehumidier. When the appliance is

used as a dehumidier, the exible pipe must not be connected. For maximum dehumidication efciency, leave

the rear discharge attachment free to discharge directly into the environment. The dehumidication mode is

recommended during autumn and winter. If used during summer, it is best to leave the exible pipe attached so

that the hot air is discharged towards the outside rather than into the room. During dehumidication, continuous

drainage should be implemented (see the next chapter, “HOW TO ELIMINATE CONDENSATE”).

Cooling, Fan Dehumidifying

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Nikko Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Nikko

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info