Bedienungsanleitung Argo Silence 11 (Seite 7 von 8) (Englisch)

665616

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

V 09/16

Choose a suitable place to position the radiator, considering the general safety warnings given in the first part of this

manual. Only use this radiator in an upright position.

Insert the plug into the electrical socket, ensuring that voltage is compliant with that specified on the convector data plate.

Select the desired temperature using the thermostat, turning

this knob clockwise: min. corresponds to minimum

temperature and max. to maximum level. The convector will

start operating only if the thermostat is above the minimum

temperature.

Then choose the power level desired through the

power selector.

Room thermostat

min = (min. temperature)

max = (max. temperature)

Power selector

0 = OFF

I = 800 W (min.) (9) – 1000 W (11)

II = 1200 W (med.)(9) - 1500 W (11)

III = 2000 W (max.)(9) - 2500 W (11)

Room temperature can be regulated by rotating the thermostat clockwise to increase or anticlockwise to

decrease temperature.

When turning the panel on, we recommend turning the thermostat knob to maximum: then, when a pleasant room

temperature has been obtained, turn the thermostat dial anticlockwise until the light of the active switch goes out. This

way the panel will maintain that room temperature constant.

To turn the convector off completely turn the power selector back to 0 and then rotate the thermostat dial anticlockwise

until it clicks off. Unplug the appliance if it will not be used for a while.

OVERHEATING SAFETY DEVICE

In the event of overheating, an additional fitted safety thermostat protects the heater against overheating and switches it

off automatically.

If the device switches itself off, disconnect the main plug from the socket.

The heater is ready for use after a short cooling-off phase (approx. 15 minutes). Plug the mains back into the socket.

If this repeats, first check that the thermostat switch is set correctly or if an object hinders the heating operation.

HOW TO CLEAN THE RADIATOR

 Always unplug and leave the radiator to cool before cleaning.

 Use a damp cloth to clean the radiator exterior and remove dust. Leave the casing to dry before using the convector

again.

 Do not allow water to enter the radiator.

 Do not use benzene, solvents or abrasive compounds to clean the radiator, as these may damage the casing.

 Use a vacuum cleaner to remove dust from the air inlet/outlet grilles.

 Ensure that the radiator is dry before inserting the plug.

 Do not use metal tools to clean the convector radiator. Any metal fragments that may detach may come into contact

with the panel’s electrical components and cause a short-circuit.

 In the event of malfunctions or damages, always contact an authorised service centre.

STORAGE OF RADIATOR

If the radiator is not used for prolonged periods, it must be stored together with this manual in its original packaging, in a

cool and dry place. Never put the appliance away when still hot. Always wait for it to cool down.

HOW TO USE THE RADIATOR

1 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Silence 11 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Silence 11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info