Bedienungsanleitung Argo X3I 27 HL (Seite 11 von 32) (Englisch)

689092

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

V 03/17

9. SLEEP button

In cool, heat or dry mode, press this button to start the SLEEP function. The icon will

appear on the remote control display. Press the button again to exit the SLEEP function. The

icon will disappear from the display.

The temperature will increase or decrease by 2 degrees over two hours according to the

function selected (cool/heat).

10. TEMP button

Pressing this button will allow you to display the set temperature, the indoor ambient

temperature, or the outdoor ambient temperature on the indoor unit's display. You can cycle

through the settings on the remote control display as shown below:

nessuna

visualizzazione

nessunavisualizzazione nodisplay

• When you select or “no display” with the remote control, the set temperature will appear

on the indoor unit's display.

• When you select

with the remote control, the indoor ambient temperature will appear on

the indoor unit's display.

• When you select

with the remote control, the outdoor ambient temperature will appear

on the indoor unit's display.

N.B.:

• It is not possible to display the outdoor ambient temperature on all models. The indoor unit

will receive the

signal but will display the set temperature.

• The set temperature will appear on the unit's display on start-up, if enabled to do so.

• When you select to display the indoor or outdoor ambient temperature, the indoor unit will

display the corresponding temperature for three to five seconds, after which it will

automatically revert to displaying the set temperature.

11. TIMER ON button

SETTING TIMER ON

This function allows you to program the air conditioner to turn on. When you press this button,

the

icon will disappear from the display and the word "ON" will flash on the remote control

display. Press "▲" or "▼" to adjust the TIMER ON setting.

Press and hold "▲" or "▼" for 2 seconds to rapidly change the time until you reach the desired

value. Press TIMER ON to confirm. The word "ON" will stop flashing. The

icon will re-

appear on the display.

CANCELLING TIMER ON

If the TIMER ON function is enabled, press the TIMER ON button to cancel the setting.

12. CLOCK button

Press this button to set the clock. The icon will flash on the remote control display. Press

"▲" or "▼" within 5 seconds to set the clock. Each time you press "▲" or "▼", the clock will

increase or decrease by 1 minute. Press and hold "▲" or "▼" for 2 seconds to rapidly change

the time. Release the button when you reach the desired time. Press "CLOCK" to confirm the

time. The

icon will stop flashing.

N.B.:

• The time displays in the 24-hour clock format.

• If no adjustment is made for 5 seconds the remote control will exit the setting mode. This also

applies to the TIMER ON/OFF function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo X3I 27 HL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info