Bedienungsanleitung Argo X3I 52HL (Seite 20 von 32) (Englisch)

689096

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

V 03/17

Distanzadall’ostruzione Distancefromobstruction

Almeno300cm Atleast300cm

Distanzadalpavimento Distancefromfloor

Almeno250cm Atleast250cm

Distanzadall’ostruzione Distancefromobstruction

Almeno50cm Atleast50cm

Distanzadall’ostruzione Distancefromobstruction

Almeno30cm Atleast30cm

Distanzadallaparete Distancefromwall

Almeno30cm Atleast30cm

Distanzadall’ostruzione Distancefromobstruction

Almeno200cm Atleast200cm

Tubodiscarico Drainpipe

Distanzadall’ostruzione Distancefromobstruction

Almeno50cm Atleast50cm

INSTALLATION WARNINGS

WARNING: Make sure that the power supply is disconnected before carrying out any work

on the unit.

WARNING: Wear appropriate personal protective equipment before carrying out any work

on the unit.

WARNING: The appliance must be reinstalled in accordance with national system

regulations.

WARNING: Wiring and installation must only be performed by a qualified technician trained

to install, modify, extend and service the unit and perform safety and functionality tests.

WARNING: Install a device, master switch or electric plug that will allow all the power from

the appliance to be switched off.

The following information is essential for correct unit installation. However, the installer

should use his or her experience to install the unit according to specific requirements.

Do not install the unit in locations where there are flammable gases or acid or alkaline

substances that may irreparably damage the copper-aluminium heat exchangers or internal

plastic components.

Do not install the unit in offices or kitchens where oil vapours mixed with treated air may

settle on the exchange coils, reducing performance, or on the unit's internal parts,

damaging the plastic components.

Choosing a location for installation

Essential requirements Indoor unit

Do not install the unit in the following locations.

Otherwise, a fault may occur.

Locations with extreme heat sources or

flammable or explosive gases or vapours.

1. Locations with high-frequency devices (e.g.

welding machines, medical equipment).

2. Locations close to coastal areas.

3. Locations with oils or fumes in the air.

4. Locations with sulphide gas.

5. Other locations that have special conditions.

Do not operate the unit in the immediate vicinity

of laundrettes, bathtubs, showers or swimming

pools.

Outdoor unit

1. There should be no obstructions near the air inlet

or outlet.

2. Choose a location where the condensate can

drain out easily without causing a nuisance.

3. Choose a convenient location to connect the

outdoor unit to the power outlet.

4. Choose a location out of the reach of children.

5. The site should be strong and solid enough to

support the weight of the indoor unit and prevent

noise or vibration.

6. The unit should be installed 2.5 m from the floor.

7. Do not install the indoor unit directly above

electrical equipment.

8. Try to keep a certain distance from fluorescent

lights.

1. Choose a location where the noise and airflow produced by the outdoor unit will not annoy neighbours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo X3I 52HL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info