Bedienungsanleitung Argo X3MI 71 SH (Seite 13 von 32) (Englisch)

689097

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

V 03/17

N.B.:

• When the 8°C heating function is enabled, the fan will operate at the default automatic speed

and cannot be adjusted. The remote control will not send a signal to the unit when the

TURBO button is pressed.

The SLEEP and 8°C heating functions cannot operate simultaneously. If the 8°C heating

function was set in cool mode, pressing the SLEEP button will cancel it. If the SLEEP

function was set in cool mode, starting the 8°C heating function will cancel it.

• When the temperature display is in °F, the remote control will show that the unit is operating

at 46°F.

Remote control button lock function

Press "▲" and "▼" simultaneously to enable or disable the remote control button lock function.

When this function is enabled,

will appear on the remote control display. If you attempt to

operate the remote control, the

icon will flash three times and no signal will be sent to the

unit.

Switching temperature display

In OFF mode, press the "▼" and "MODE" buttons simultaneously to switch from a temperature

display in °C to °F.

Operating guide

1. When you connect the power, press the "ON/OFF" button on the remote control to turn the

air conditioner on.

2. Press the MODE button to select the desired operating mode: AUTO, COOL, DRY, FAN or

HEAT.

3. Press "▲" or "▼" to adjust the desired temperature. (The temperature cannot be adjusted

in automatic mode.)

4. Press the "FAN" button to set the desired fan speed: automatic, low, medium or high.

5. Press the "SWING" button to adjust the fan's angle of airflow.

Replacing the remote control batteries

1. Remove the battery compartment cover, marked with

(see image to right), by sliding it in the direction of

the arrow.

2. Use only two AAA – LR03 1.5V batteries. Make sure

the + and – ends are facing the correct direction.

3. Slide the battery compartment cover back into place.

trasmittente

segnale

coperchio vano batterie

rimozione

reinserimento

batterie

trasmittentesegnale signaltransmitter

batterie batteries

reinserimento close

rimozione open

coperchiovanobatterie batterycompartmentcover

N.B.:

 When the unit is operating, point the remote control's signal transmitter at the indoor unit's

receiver.

 The distance between the transmitter and the receiver must not exceed 8 metres and

should remain free of obstacles.

 If the room contains a fluorescent light or cordless telephone, signal interference is likely to

occur.

 When the remote control is not used for a month or more, remove the batteries.

 Use batteries of the same type when replacing the batteries, as necessary.

 If the icons on the remote control display are blurred or not visible, replace the batteries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo X3MI 71 SH Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info