Bedienungsanleitung Argus dc 1510 (Seite 8 von 18) (Englisch)

290006

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

NOTE: If you do not hear the "beep" and/or the frame counter does not count down 1 frame, the

photo has not yet been taken. Press Shutter button again to take the picture.

Tip:

It is recommended that you take a few trial shots at different distances to see the results of each

photo.

Changing Capture Modes

Continuous Mode

1. Press Mode button until

is shown on the LCD panel

2. Hold down the Shutter button to take photos continuously until the frame counter counts down to

00.

NOTE: In Continuous mode, 6 photos will be taken in one second.

Self-Timer

1. Press Mode button until

appears on the LCD panel

2. Press Shutter button. A beep will sound and the LED will blink for 10 seconds before a photo is

taken.

Deleting Photos

Deleting All Photos

1. Press Mode button until

is shown in the LCD panel.

2. Press Shutter button and

will flash in the LCD panel. While is flashing, press Shutter

button again. You will hear two beeps and all photos will be cleared.

NOTE: If Shutter button is not pressed while

is flashing, the frame counter will appear in the

LCD panel in 5 seconds.

Deleting Last Photo Taken

1. Press Mode button until

is shown on the LCD panel

2. Press Shutter button and the last taken photo will be deleted and the frame counter will change in

the following pattern:

When camera is in High Resolution mode:

• Erasing the last 1,2 or 3 photos of low resolution will toggle frame counter unchanged.

• Erasing the last 4 photos of low resolution will toggle frame counter to go up by 1

• Erasing the last photo of high resolution will toggle frame counter to go up by 1

When camera is in low resolution mode:

• Erasing the last photo of high resolution will toggle frame counter to go up by 4

• Erasing the last photo of low resolution will toggle frame counter to go up by 1

Connecting digital camera to PC

Install Arcsoft programs and camera drivers in Windows 98SE/Me

NOTE: The graphics shown are based on the user interface in Windows 98SE

1. Put the program CD into the CD-ROM drive, Autorun will commence.

2. Select 1 to install the Arcsoft programs

3. Change Destination Folder if necessary

4. Select components to install

5. Change program folder name if necessary

6. Click Finish button to complete Setup

Install camera drivers:

1. Select 2 to install the camera drivers

2. Choose Setup language

3. Click Finish button to complete Setup and restart your computer

4. After your computer is restarted, connect the camera and computer with the USB cable and the

computer will recognize the camera.

Note: The installed camera drivers may conflict other USB devices in your computer system.

Install Arcsoft programs and camera drivers in Windows 2000/XP

NOTE: The graphics shown are based on the user interface in Windows XP

1. Put the program CD into the CD-ROM drive, Autorun will commence.

2. Select 1 to install the Arcsoft programs

3. Change Destination Folder if necessary

4. Select components to install

5. Change program folder name if necessary

6. Click Finish button to complete Setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argus dc 1510 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argus dc 1510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info