Bedienungsanleitung Ariston AB1030C (Seite 12 von 15) (Englisch)

47629

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

If despite all this your washer-dryer is still not running properly,

call your local Authorized Service Centre providing the

following information:

- fault

- model code (Mod. ....)

and serial number (S/N ....)

shown on the data plate at the back of your washer.

Never use the services of an unauthorised servicing technician

and insist on the use of original spare parts.

Installation

Transit packing

After removing the packing, check the appliance for damage.

If you have any doubts do not use the washer and call a qualified

technician. Keep the packaging components (plastic bags,

polyester foam, nails etc.) out of the reach of children since

they could be dangerous. The interior of the washer-dryer, has

an oscillating unit which is fixed on the back by 3 screws

during transport (figure 3). Before starting up the washer-dryer,

release the unit, by unscrewing the 3 screws. Seal the screw

holes with the plastic plugs supplied with the appliance.

Levelling

The washer-dryer must be perfectly levelled. To level the

appliance, only the front feet need to be adjusted

(see fig. 4); remember that the inclination of the working

surface must not be more than 2 degrees. If the washer-dryer

is installed on a carpeted floor, check that there is sufficient

ventilation space between the floor and the bottom of the

washer-dryer.

Water supply

Both hot and cold water supplies are preferable and they should

be between 34.5kN/m²(5lb/in²) and 1034.2kN/m² (150lb/in²)

pressure. The hose having the red end fitting should be en-

countered between the hot supply and the threaded connec-

tion adjacent to the letter H on the rear of the machine. The

hose having the white end fittings should be connected be-

tween the cold supply and the threaded connection adjacent

to the letter C on the rear of the machine (see fig. 5). Remem-

ber to insert a sealing washer at each connection to ensure

watertight joints. Do not overtighten the connections by

using tools -hand tight is sufficient to prevent leaks. It is gener-

ally more convenient to have these supplies away from the

sink taps. Where no suitable hot water supply is available or it

does not meet these requirements, both inlet hoses may be

connected to a cold supply by using two taps etc., or a «T»

junction on the plumbing (see fig. 6) however, use of cold

water only will increase programme times.

Note: the maximum temperature should not exceed 70°C

(158°F).

Drain hose

The drain hose (hooked pipe) is secured to the rear of the

machine by support clips and may be routed to right or left as

required (see fig. 7). The drain hose should be placed in a

stand pipe with a minimum internal diameter of 38 mm (1½

inches) or it can be positioned over a sink (see fig. 8) or it can

be connected as shown in fig. 9. The height of stand pipe or

sink should be between 60 and 100 cm (24 and 40 inches).

Care must be taken that the hose is not obstructed, twisted,

submerged or kinked. If the hose is connected with an airtight

joining, provision should be made to prevent syphoning.

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston AB1030C Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info