Bedienungsanleitung Ariston ARWXF 129 W (Seite 5 von 18) (Englisch)

609131

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

A & B = 25" (62 cm) min. / 34" (86 cm) max.

Floor Standpipe

Wall Standpipe

Fig. 4

Standpipe Drain System - Installations require a minimum

1 ¼” (3.2 cm) diameter standpipe with a minimum carry

away capacity of 7 gallons (26 liters) per minute.

Wall or Floor Standpipe Drain System - The top of the

standpipe must be between 25” (62 cm) - 34” (86 cm)

from the bottom of the washer (Fig. 4).

Sink Drainpipe System

Entry into the sink drain

system must be above the trap (Fig. 5). When routing the

drain hose through cabinets or walls, use a protective ma-

terial such as electrical or duct tape to cover sharp edges

that could damage the drain hose. Use a suitable clamp

to secure the drain hose to the “Y” branch or the disposer.

With a sink drainpipe system, you may connect directly:

1) to a disposer by following the manufacturers attachment

method.

2) directly to a “Y” branch tail piece (available at most

hardware stores).

3) Through the floor to a separate trap. The trap must be

vented to prevent siphoning. To provide proper venting,

install an Air Gap Kit (available at most hardware stores).

4) To the to the faucet using a Faucet Adapter Kit (available

separately).

• Use a U-Clamp (provided in your accessories packet)

or suitable item to secure the outlet end of the drain hose

(pre-installed on the back of your machine).

25" (62 cm) min.

with an air break

Laundry Sink Drain

Fig. 5

Sink Drain W/ "Y" Branch Tailpiece

Important:

Make sure that the drain hose is

not kinked and that water flow is not restricted.

Connecting Water Inlet

If the water pipes you will be connecting to are new or

unused, run the water until clear to remove any debris that

could clog the water valve screens or valves before con-

necting the machine. NOTE: Supply shut-off valves should

be easily accessible.

1. Screw the cold water fill

hose (C blue connector) onto

the cold water supply until

tight.

2. turn on the cold water

supply and check for leaks,

tighten if necessary.

3. Screw the hot water fill

hose (H red connector) onto

the hot water supply until tight.

4. Turn on the hot water supply and check for leaks,

tighten if necessary.

Drainage

• Standpipe Diameter/Capacity - Needs a 1 ¼”

minimum diameter standpipe with a minimum carry-away

capacity of 7 gallons per minute.

• Top of Standpipe - Must be between 25” - 34” high

from the bottom of the machine.

• Outlet End of Drain Hose (provided with the unit)

- Must be at least 20” above the bottom of the washer-

dryer. An air break must be available at the standpipe to

avoid siphoning. No more than 6” of the drain hose should

be inserted into the drain pipe to prevent siphoning.

Connecting the drain hose

It is possible for the water to be discharged into a sink,

standpipe or drainpipe, but an air break must be available

at a min. 20” height to prevent the machine from siphoning

(Fig. 6).

Important:

Water pressure MUST range wi-

thin the values indicated on the “Technical Data”

chart.

Important:

Do not use excessive force. Da-

mage to the couplings can result. The couplings

should be tightened by hand; a tool should only

be used if a leak occurs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston ARWXF 129 W Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info