Bedienungsanleitung Ariston ASL60V (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

48095

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

●

DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left

for a drying programme.

The delay time is displayed in hours and counts down

each hour.

The time to end is displayed in hours and minutes

and counts down each minute, this includes the cool

tumble phase. When timed programmes are selected

the time displayed throughout the cycle is the actual

time remaining.

When a sensing programme is selected the time

displayed is an estimate of the time remaining. When

the programme is selected the display shows the time

required to dry a full load, after around 10 minutes the

controller calculates a better estimate of the cycle

time.

The colons between the hours and minutes in the

display flash to show that the time is counting down.

When the programme finishes its cool tumble phase

the display will show .

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed

by a fault code number (see Troubleshooting).

●

Door Opening

Opening the door during a programme will stop the

dryer and have the following effects:

●

All 4 progress lights come on.

●

During a delay phase the delay will continue

to count down. The start button must be

pressed to resume the delay programme.

The progress lights will change to show

current status.

●

During the drying part of the programme, the

time to end count continues but the colons

do not flash. The start button must be

pressed to resume the programme. The

progress lights will change to show the

current status.

●

During the cool tumble or post creasecare

phase of a drying programme and anytime

during an Airing or Cool Tumble programme,

the programme will finish. Pressing the start

button will re-start a new programme at the

beginning.

●

Changing the programmes knob will select a

new programme, after you press the start

button. You can use this to select the Cool

Tumble programme to cool the clothes, if you

find them dry enough.

●

Note

If you have a power cut, switch off the power or

remove the plug, press the START button and the

programme will resume.

●

PROGRAMMES knob

! Warning, if after pressing the start button, the

programmes knob position has changed, the new

position will NOT change the programme selected.

! Position 0, turning the knob to position 0 resets

and cancels a programme, the display shows .

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before

an option can be selected. Not all options are available

for all programmes (see Start and Programmes). If an

option is not available and you press the button, the

buzzer will beep three times. If the option is available

there will be one beep and the option light next to the

button lights to confirm the selection.

After the start button has been pressed only the

Alarm, Pre Creasecare and Post Creasecare options

can be changed.

Time Delay

The start of some programmes (see Start and

Programmes) can be delayed for up to 18 hours.

Press this button, the display shows and the

option light comes on. Press again and a 1 hour

delay is selected and the display indicates 1hr, each

further press of the button adds 1hr to the delay.

When 18hr is displayed a further press the display

shows and after a couple of seconds cancels

the delay. You can also cancel the delay by turning

the programmes knob to 0, wait for the buzzer to

beep and then turn back to your selected programme.

Pre Creasecare

This option is only available if a delayed start has

been selected. It tumbles the clothes occasionally

during the delayed period to help prevent creases

developing.

High Heat

When available this button selects high heat. Press

this button and a high heat setting is selected and

the light alongside the button comes on.

Timed programmes have a default of low heat, if the

light alongside the button is on then pressing the button

selects a low heat setting and the light goes out. The

heat icon on the display will also change.

Alarm

Available on all programmes and allows the buzzer

to give a signal at the end of the drying cycle, to

remind you that the clothes are ready to be removed.

Press the button and the light will show that the

option is selected.

Post Creasecare

When available and selected, the clothes are

occasionally tumbled after the end of the drying and

cool tumble cycles, to help prevent creases

developing should you not be available to remove

the load immediately the programme is complete.

OFF

E88

The Controls

Installation

Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance and

Care Troubleshooting Service

Start and Programmes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston ASL60V Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info