Bedienungsanleitung Ariston CDE12X (Seite 15 von 20) (Englisch)

23732

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Margherita - Iinstructions for installation and use

ARGHERITA

Mounting the Parts onto

the Face of the Machine

- Mount the hinge supports onto

the face of the machine,

positioning the hole indicated by

the arrow in fig. 1 towards the

inside of the face and using the

type C screws.

- Mount the magnetic plate on

the opposite side, at the top,

using the two type B screws.

- Place the spacer illustrated in

fig. 4/B between the appliance

front and the magnet receiver.

Using the Drilling

Template

- To trace the positions of the

holes on the left-hand side of the

panel, align the drilling template

to the top left side of the panel

using the lines traced on the

extremities as a reference.

- To trace the positions of the

holes on the right-hand side of

the panel, align the drilling

template to the top right side of

the panel.

- Use an appropriately sized router

to mill the holes for the two

hinges, the rubber plug and the

magnet.

Mounding the Parts onto

the Wooden Panel (Door)

- Insert the hinges into the holes

(the movable part of the hinge

must be positioned facing away

from the panel) and fasten them

with the 4 type A screws.

- Insert the magnet into the top

hole on the opposite side of the

hinges and fasten it with the two

type B screws.

- Insert the rubber plug into the

bottom hole.

The panel is now ready to be

mounted onto the machine.

Mounting the Panel into

the machine

Insert the nib of the hinge

(indicated by the arrow in fig. 2)

into the hole for the hinge and

push the panel towards the front

of the machine. Fasten the two

hinges with the type D screws.

Fastening the plinth

guide

If the machine is installed at the

end of a set of modular cabinets,

mount either one or both of the

guides for the base molding (as

shown in fig. 8). Adjust them for

depth based on the position of

the base molding, and, if

necessary, fasten the base to the

guides (fig. 9).

This is how to assemble the

plinth guide (fig.8):

Fig. 6 Fig. 7 Fig. 9

Adjusting the appliance

height

The height of the appliance can

be adjusted (from 815 mm to

835 mm), by turning the 4 feet.

Should you require the appliance

to be placed higher than the

above height, you need to use the

following accessories to raise it

to up to 870 mm:

- the two crossbars (G)

- the 4 feet (H)

- the 4 screws (I)

- the 4 nuts (L)

then perform the following

operations (fig. 11):

remove the 4 original feet, place

a crossbar G at the front of the

appliance, fastening it in place

using screws I (screwing them in

where the original feet were) then

insert the new feet H.

Repeat the same operation at the

back of the appliance.

Now adjust feet H to raise or

lower the appliance from 835

mm to 870 mm.

Once you have reached the

desired height, lock nuts L onto

crossbar G.

Fig. 11

To adjust the appliance to a

height between 870 mm and 900

mm, you need to mount strip M,

adjusting feet H to the required

height.

Insert the strip as follows:

loosen the three screws N

situated at the front of the Top

cover of the appliance, insert

strip M as shown in fig. 12, then

fasten screws N.

Accessories provided for

the height adjustment

The following can be found inside

the polystyrene lid (fig. 10):

2 crossbars (G),

1 strip (M)

the following can be found inside

the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Fasten angle P using screw R,

insert plinth guide Q into the

special slot and once it is in the

desired position, lock it in place

using angle P and screw R.

Inserting the machine

into the Cabinet

- Push the machine into the

opening, aligning it with the

cabinets (fig. 6).

- Regulate the adjustable feet to

raise the machine to the

appropriate height.

- To adjust the position of the

wooden panel in both the vertical

and horizontal directions, use the

C and D screws, as shown in fig. 7.

Important: close the lower part of

the appliance front by ensuring

that the plinth rests against the

floor.

Fig. 10

Fig. 12

Fig. 8

570

815

540

595

820 ÷ 900

600 m

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston CDE12X Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston CDE12X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info