Bedienungsanleitung Ariston Clas HE R (Seite 19 von 64) (Englisch)

719964

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

/ 19

INSTALLATION

Fitting the Coaxial Flue

(Ø 60 / 100 Vertical)

Note: See table for maximum and minimum ﬂue runs.

Contents:

1x Conical Adaptor (60/100mm)

1x Vertical Flue Kit (80/125mm)

The vertical ﬂue kit is supplied with a specially designed weather

proof terminal ﬁtted, it can be used either with a ﬂat roof or a

pitched roof.

The Vertical ﬂue kits useable lengths with the pitched roof ﬂashings

are indicated in Fig. 7.

Before proceeding to ﬁt the ﬂue, ensure that the maximum ﬂue

length has not been exceeded (See the tables) and that all elbows

and bends have been taken into consideration, for each additional

90° elbow 1 metre must be subtracted from the total ﬂue length,

and for each 45° 0.5 metres must be subtracted from the total ﬂue

length (the height of the vertical adaptor and a 45° bend can be

seen in Fig. 8).

Mark the position of the ﬂue hole in the ceiling and/or roof (see Fig.

7 for distance from wall to the centre of the ﬂue).

Cut a 130mm diameter hole through the ceiling and/or roof and ﬁt

the ﬂashing plate to the roof.

DO NOT cut the vertical ﬂue kit.

To connect the vertical ﬂue kit directly to the boiler, place the vertical

starter kit (Part No. 3318079) (see Fig. 7) onto the exhaust manifold

and secure with the clamp, ﬁt the vertical adaptor onto the vertical

starter kit (note: there is no need to use a clamp to secure this as it

is a push ﬁt connection), the vertical ﬂue kit must then be inserted

through the roof ﬂashing, this will ensure that the correct clearance

above the roof is provided as the terminal is a ﬁxed height.

Should extensions be required, they are available in 1 metre (Part No.

3318077), 500mm (Part No. 3318078) and they must be connected

directly to the vertical starter kit before connecting the adaptor to

allow the vertical ﬂue kit to be ﬁtted. In the event that extension

pieces need to be shortened, they must only be cut at the male end

and it must be ensured that the inner and outer ﬂue remain ﬂush.

When utilising the vertical ﬂue system, action must be taken to

ensure that the ﬂue is supported adequately to prevent the weight

being transferred to the appliance ﬂue connection by using 1 ﬂue

bracket per extension.

When the ﬂue passes through a ceiling or wooden ﬂoor, there must

be an air gap of 25mm between any part of the ﬂue system and any

combustible material. The use of a ceiling plate will facilitate this.

Also when the ﬂue passes from one room to another a ﬁre stop must

be ﬁtted to prevent the passage of smoke or ﬁre, irrespective of the

structural material through which the ﬂue passes.

180 mm

Vert Adaptor

(supplied with ue kit)

Vertical Starter

Part No: 3318079

* This length will vary

according to the type

of ashing installed

Total length

of Vertical Kit

1355 mm

Useable length

of Vertical ue

690 mm*

Fig. 7

Fig. 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston Clas HE R Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info