Bedienungsanleitung Ariston E-Combi One (Seite 11 von 80) (Englisch)

719960

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

/ 11

INSTALLATION

Reference Standards

In the United Kingdom, the installation and initial start-up of the

boiler must be by a Gas Safe registered installer in accordance

with the installation standards currently in effect, as well as with

any and all local health and safety standards i.e. Gas Safe.

In the Republic of Ireland the installation and initial start-up of

the appliance must be carried out by a Competent Person in

accordance with the current edition of I.S.813 “Domestic Gas

Installations” and the current Building Regulations, reference

should also be made to the current ETCI rules for electrical

installation.

The installation of this appliance must be in accordance with

the relevant requirements of the Local Building Regulations,

the current I.E.E. Wiring Regulations, the by-laws of the local

authority, in Scotland, in accordance with the Building Standards

(Scotland) Regulation and Health and Safety document No. 635,

“Electricity at Work Regulations 1989” and in the Republic of

Ireland with the current edition of I.S. 813 and the Local Building

Regulations (IE).

C.O.S.H.H.

Materials used in the manufacture of this appliance are non-

hazardous and no special precautions are required when

servicing.

Codes of Practice

Installation should also comply with the following British

Standards Code of Practice (refer to the most recent version):

BS 7593: Treatment of water in domestic hot water

central heating systems

BS 5546: Installation of hot water supplies for

domestic purposes

BS 5440-1: Flues

BS 5440-2: Air supply

BS EN 12831 - BS EN 14336:

Forced circulation hot water systems

BS 6798: Installation of gas red hot water boilers

of rated input not exceeding 70kW

BS 6891: Installation of low pressure gas pipes up to 28mm

BS 7671: IEE Wiring Regulations

BS 4814: Specication for expansion vessels

BS 5482: Installation of L.P.G.

Technical Bulletin TB143 Flue Gas Analysis

and in the Republic of Ireland in accordance with the following

codes of practice:

I.S. 813 Domestic Gas Installations

Avoid installing the boiler where the air inlet can be polluted

by chemical products such as chlorine (swimming pool area), or

ammonia (hair dresser), or alkalin products (launderette).

Flue

Detailed information on ue assembly can be found in the

“Connecting the Flue” section.

The boiler must be installed so that the ue terminal is exposed

to the free passage of external air at all times and must not be

installed in a place likely to cause nuisance. It must not be

allowed to discharge into another room or space such as an

outhouse or closed lean-to.

Condensing boilers have a tendency to form a plume of water

vapour from the ue terminal due to the low temperature of

the ue gasses. The terminal should therefore be located with

due regard for the damage or discolouration that may occur

to building within the vicinity and consideration must also be

given to adjacent boundaries, openable windows should also

be taken into consideration when siting the ue.

The minimum acceptable clearances are shown below:

- A Directly below an opening, window, etc 300 mm

- B Horizontally to an opening, window, etc 300 mm

- C Below gutters, soils pipes or drain pipes 75 mm

- D Below eaves 200 mm

- E From vertical drain pipe or soil pipe 75 mm

- F From internal or external corner 300 mm

- G Above ground, roof or balcony level 300 mm

- H From a surface facing the terminal 600 mm

- I From a terminal facing a terminal 1200 mm

- J Vertically from a terminal on the same wall 1500 mm

- K Horizontally from an terminal on the same wall 300 mm

- L Fixed by vertical ue terminal

Note: the flue must Not be iNstalled iN a place likely to cause a

NuisaNce aNd positioNed to eNsure that products of combustioN do

Not discharge across a bouNdary

It may be necessary to protect the terminal with a guard, if this

is the case it will be necessary to purchase a stainless steel

terminal guard. Reference should be made to the Building

Regulations for guidance.

Ventilation

The room in which the boiler is installed does not require

specic ventilation. If the boiler is installed in a cupboard or

compartment ventilation is not required for cooling purposes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston E-Combi One Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston E-Combi One

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info