Bedienungsanleitung Ariston E-Combi One (Seite 21 von 80) (Englisch)

719960

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

/ 21

INSTALLATION

Fitting the Coaxial Flue

(Ø 60 / 100 Vertical)

Note: See table for maximum and minimum ue runs.

Contents:

1x Conical Adaptor (60/100mm)

1x Vertical Flue Kit (80/125mm)

The vertical ue kit is supplied with a specially designed

weather proof terminal tted, it can be used either with a at

roof or a pitched roof.

The Vertical ue kits useable lengths with the pitched roof

ashings are indicated in Fig. 7.

Before proceeding to t the ue, ensure that the maximum ue

length has not been exceeded (See the tables) and that all

elbows and bends have been taken into consideration, for each

additional 90° elbow 1 metre must be subtracted from the total

ue length, and for each 45° 0.5 metres must be subtracted from

the total ue length (the height of the vertical adaptor and a 45°

bend can be seen in Fig. 8).

Mark the position of the ue hole in the ceiling and/or roof (see

Fig. 7 for distance from wall to the centre of the ue).

Cut a 130mm diameter hole through the ceiling and/or roof and

t the ashing plate to the roof.

DO NOT cut the vertical ue kit.

To connect the vertical ue kit directly to the boiler, place the

vertical starter kit (Part No. 3318079) (see Fig. 7) onto the exhaust

manifold and secure with the clamp, t the vertical adaptor onto

the vertical starter kit (note: there is no need to use a clamp to

secure this as it is a push t connection), the vertical ue kit must

then be inserted through the roof ashing, this will ensure that

the correct clearance above the roof is provided as the terminal

is a xed height.

Should extensions be required, they are available in 1 metre

(Part No. 3318077), 500mm (Part No. 3318078) and they must be

connected directly to the vertical starter kit before connecting

the adaptor to allow the vertical ue kit to be tted. In the event

that extension pieces need to be shortened, they must only be

cut at the male end and it must be ensured that the inner and

outer ue remain ush.

When utilising the vertical ue system, action must be taken

to ensure that the ue is supported adequately to prevent the

weight being transferred to the appliance ue connection by

using 1 ue bracket per extension.

When the ue passes through a ceiling or wooden oor, there

must be an air gap of 25mm between any part of the ue

system and any combustible material. The use of a ceiling

plate will facilitate this. Also when the ue passes from one

room to another a re stop must be tted to prevent the passage

of smoke or re, irrespective of the structural material through

which the ue passes.

180 mm

Vert Adaptor

(supplied with ue kit)

Vertical Starter

Part No: 3318079

* This length will vary

according to the type

of ashing installed

Total length

of Vertical Kit

1355 mm

Useable length

of Vertical ue

690 mm*

Fig. 7

Fig. 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston E-Combi One Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston E-Combi One

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info