Bedienungsanleitung Ariston E-Combi One (Seite 36 von 80) (Englisch)

719960

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

36 /

COMMISSIONING

If the value measured corresponds to the value given in the

table, adjustment is complete, otherwise start the setting

procedure again.

Attention! If the value of the CO2 at the minum power has

been changed, it is necessary repet the adjusting at maximum

gas ow.

Operation 5 - Ending the adjustment

Exit cleaning mode by pressing RESET.

Stop the draw-off.

Verify and repair any leaks of gas.

Ret the front panel to the device.

Ret the blanking cover at combustion test point.

menu 2 - Boiler parameters

submenu 3 - parameter 1 Maximum Heating Power adjustment

submenu 2 - parameter 0

Soft light Ignition

submenu 3 - parameter 5 Heating ignition delay

Maximum Heating Power adjustment

The maximum heating power can be adjusted to between the

maximum power allowed by the boiler and the minimum power).

The display shows the value between 100% (“100” on the

display) and 0% (“0”) of this interval.

To check the maximum heating power, access menu 2/sub menu

3/parameter 1, check the value and, if necessary, modify it as

indicated in the Gas Regulation table below. (See page 40 for

more details).

Checking slow ignition power

The soft light can be adjusted between the maximum power

(shown on the display as “100”, i.e. 100%) and the minimum

power (shown on the display as “1”, i.e. 1%).

To check the slow ignition power, access menu 2/sub menu 2/

parameter 0.

Heating ignition delay adjustment

This parameter – menu 2/sub menu 3/parameter 5 - can be used

to manually (0) or automatically (1) set the delay time before the

subsequent reignition of the burner after it has switched off on

reaching the desired temperature in central heating mode.

By selecting manual, it is possible to set the delay in minutes

using the successive parameter (menu 2/sub menu 3/parameter

6), to a time between 0 and 7 minutes.

Automatic selection means that the boiler will establish the

delay time based on the set-point temperatureinstallation

instructions. Ensure the ue gas analyser used is calibrated and

set for the gas group the appliance is being adjusted for.

12. Check the appliance for gas leaks using gas leak detection

uid.

13. Afx the label to the appliance that is supplied with the

conversion kit.

27,4

21,4

3,4

3,9

E-COMBI ONE / E-SYSTEM ONE 30

E-COMBI ONE / E-SYSTEM ONE 24

Table summarising changes

(*) Gas diaphragm integrated in the air/gas mixer

(NON-REMOVABLE)

1 32 4

parameter

E-COMBI ONE

E-SYSTEM ONE

24 30

G20 G31 G20 G31

Lower Wobbe index (15°C, 1013 mbar) ( MJ/m

) 45,67 70,69 45,67 70,69

Inlet Gas pressure

20 30-37 20 30-37

Slow ignition 220

64 62

Maximum C. H.power Adjustable (%) 231

56 60

Minimum power (%) 233

3 3

Max CH power (%) 234

75 84

Max DHW power (%) 232

90 90

Gas diaphragm ((Ø) mm 5,0 (*) 3,6 5,8 (*) 4,0

Gas ow max/min

(15°C, 1013 mbar)

(nat - m3/h) GPL - kg/h)

max D.H.W 2,751 2,020 3,175 2,330

max C.H 2,328 1,709 2,963 2,175

min 0,391 0,287 0,455 0,334

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston E-Combi One Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston E-Combi One

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info