Bedienungsanleitung Ariston E-System One (Seite 44 von 80) (Englisch)

719961

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

44 /

SETTINGS - ADJUSTMENT - PROBLEM IDENTIFICATION MENUS

sub-menu

Parameter

Description value

default setting

4 2 4 Compensation from 0 to 20 20

if setting = 0, the temperature taken from the ambient sensor does not affect the calculation of the setting. If setting = 20,

the temperature taken has maximum inuence on the setting.

4 2 5 Zone 1 heating MAXIMUM temperature

setting

from 35 to 85 °C 82 if parameter 420 = 1

from 20 to 45 °C 45 if parameter 420 = 0

4 2 6 Zone 1 heating MINIMUM temperature

setting

from 35 to 85 °C 35 if parameter 420 = 1

from 20 to 45 °C 25 if parameter 420 = 0

4 3 DIAGNOSTICS

4 3 4 Zone 1 heat request 0 = OFF

1 = ON

5 ZONE 2 PARAMETER

5 0 ZONE 2 TEMPERATURE SETTING

5 0 2 Heating xed temperature setting

“Heating xed temp”

from 35 to 82 °C

(high temperature - para. 420

=1)

70 Activated only with temperature

control and xed temperature

(see 521)

from 20 to 45 °C

(high temperature - para. 420

=0)

5 2 ZONE 2 SETTING

5 2 0 Heating appliance temperature value setting 0 = from 20 to 45°C

(low temper ature)

1 = from 35 to 85°C

(high temperature)

1 select in the appliance type

base

5 2 1 Basic heating control type selection type

depending on the peripheral devices

connected

0 = xed ow temperature

1 = device On/Off

2 = NOT PRESENT

3 = external sensor only

4 = NOT PRESENT

1 To activate heating control,

press the AUTO button. The

display lights up the AUTO

symbol

5 2 2 Slope from 0_2 to 0_8 (low temperature)

from 1_0 to 3_5 1_5 (high temperature)

- see graph on the previous page

If the external sensor is used, the boiler calculates the most suitable heating ow temperature taking the external

temperature and the type of appliance into account.

The type of curve must be chosen according to the type of appliance radiator and the heat losses present in the building.

5 2 3 Parallel curve shift Zone 2 Offset from - 7 to + 7 (low temperature) 0

from - 14 to + 14

(high temperature)

To adapt the thermal curve to the appliance requirements, it is possible to perform a parallel shift of the curve in order

to alter the calculated ow temperature and therefore the ambient temperature.

By accessing this parameter or pressing the buttons 12 the curve can be shifted in a parallel manner as indicated in the

gure shown below.

The value is indicated on the display:

- from -7 to +7

(low temperature)

- from -14 to +14

(high temperature)

Each step represents a ow temperature increase/decrease of 1°C in relation to the

set-point value.

5 2 4 Compensation from 0 to 20 20 if setting = 0, the temperature

taken from the ambient sensor

does not affect the calculation

of the setting. If setting = 20,

the temperature taken has

maximum inuence on the

setting.

5 2 5 Zone 2 heating MAXIMUM temperature

setting

from 35 to 85 °C 82 if parameter 520 = 1

from 20 to 45 °C 45 if parameter 520 = 0

5 2 6 Zone 2 heating MINIMUM temperature

setting

from 35 to 85 °C 35 if parameter 520 = 1

from 20 to 45 °C 25 if parameter 520 = 0

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston E-System One Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston E-System One

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info