Bedienungsanleitung Ariston EVOS 50 MC4 (Seite 26 von 88) (Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566566

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

1 2N

3. ELECTRICAL CONNECTIONS

3.1 Internal unit connection

1. Remove the terminal board cover.

2. Feed the internal unit/external unit connection cable from the rear of the internal unit

and prepare the tip of the cable.

3. Connect the conductors to the screw terminals in accordance with the numbering.

4. Use the wire clamp situated underneath the terminal board of the electrical connec-

tions.

5. Put the cover back in place, ensuring it is positioned correctly.

NOTE the connection cables must not pass near electrical boxes, wiﬁ routers or other

cables.

3.2 External unit connection

1. Remove the cover.

2. Connect the conductors to the screw terminals using the same numbering used in the

internal unit. Screw the terminal board screws tightly to avoid any loosening.

3. Fasten the cables using the cable clamp.

4. Put the cover back in place, ensuring it is positioned correctly.

NOTE: remove the sheath from both ends of the connection wires in the cable as illus-

trated in the ﬁ gure. Make sure the connection wires do not come into contact with the

piping or other metal parts.

Type of electrical connection

Model Power supply Switch type Connection wire Power supply cable

2,5 kW 220-240V˜50Hz 10 A 5G 1 mm

3G 1 mm

3,5 -5 kW 220-240V˜50Hz 16 A 5G 1,5 mm

3G 1,5 mm

7 kW 220-240V˜50Hz 25 A 5G 2,5 mm

3G 2,5 mm

NOTE: Electrical connection between the internal and external units must be performed

using a HO7RN-F cable

3.3 Connection to the electricity mains

The connection of the appliance must comply with European and national regulations and

must be protected by a 30 mA differential switch.

Connection to the electricity mains supply must be performed using a ﬁ xed connection

(not with a mobile plug), equipped with an omnipolar switch complying with all applicable

CEI-EN regulations in force (minimum distance between contacts 3mm, switch preferably

equipped with fuses).

Proper connection to an efﬁ cient earthing system is essential for ensuring the safe opera-

tion of the device.

15 mm

70 mm

WARNING:

- Before carrying out any electrical connection make sure that the units have been disconnected from the elec-

tricity supply and that the systems which the appliance must be connected to comply with applicable regula-

tions.

- Only use cables with a suitable section.

- Allow some extra length on the connection cables to allow for future maintenance.

- Never connect the power supply cable by cutting it in half as this could cause a blaze.

- If the power supply cable is damaged, it must be replaced by the manufacturer or by its technical assistance

service, or at least by a suitably qualiﬁ ed individual, in order to prevent all hazards

POWER SUPPLY

(HO7RN-F)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston EVOS 50 MC4 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston EVOS 50 MC4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info