Bedienungsanleitung Ariston HC 9 IX (Seite 7 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

454544

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Installation - Fig. 5

The cooker hood must be placed at a minimum distance of

60 cm from the cooking plane for electric cookers and 75cm

for gas or mixed cookers.

The hood is equipped with a top air outlet B for discharge

of fumes to the outside (Ducting version – exhaust pipe

and pipe fixing clamps not provided).

Should it not be possible to discharge cooking fumes and

vapour to the outside, the hood can be used in the filter

version, fitting an activated carbon filter and the deflector F

on the support (bracket) G, fumes and vapours are recycled

through the top grille H by means of an exhaust pipe

connected to the top air outlet B and the connection ring

mounted on the deflector F (exhaust pipe and pipe fixing

clamps not provided).

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Preliminary information for installation of the hood:

Disconnect the hood during electrical connection, by turning

the home mains switch off.

First decide which functioning version is better for you.

If you decide to use the hood in ducting version we suggest

to position the upper section of the chimney so that the oulet

slots are not visible once installation has ended, on the

contrary if is decided to use the hood in filter version BE

SURE that the side with slots is up (see also A-B-C sequence

on on Fig. 5).

1. Rest the suction unit on a flat surface and thread the lower

part of the hood onto it (remove the grease filter/s).

2. Make all the electrical connections between the two

parts.

3. Fasten the hood to the suction unit using 4 screws.

4. Using a pencil, draw a line on the wall, extending up to

the ceiling, to mark the centre. This will facilitate

installation.

5. Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must correspond

to the centre line drawn on the wall, and the bottom edge

of the drilling template must correspond to the bottom

edge of the hood: bear in mind that, when installation is

complete, the underside of the hood must be at least 60

cm above the cooker top in the case of electric cookers,

and at least 75 cm above the cooker top in the case of

gas or mixed cookers.

6. Rest the support bracket on the drilling template so that

it coincides with the dotted rectangle, mark the two outer

holes and drill them, remove the drilling template, insert

2 wall plugs and fix the hood support bracket into place

using two 5x45mm screws.

7. Hang the hood on the bracket.

8. Adjust the distance of the hood from the wall.

9. Adjust the horizontal position of the hood.

10.From inside the suction unit, use a pencil to mark the hole

to be used for final fixing of the hood.

11.Remove the hood from the bracket.

12.Drill at the point marked (Ø8mm - see operation 10).

13.Insert 1 wall plug

14.Rest the chimney support bracket G against the wall,

touching the ceiling. Use the support bracket as a drilling

template (the small slot formed on the support must

coincide with the line drawn on the wall as above –

operation 4) and mark 2 holes with a pencil, dril the holes

(Ø8mm), insert 2 wall plugs.

15.Fix the chimney support bracket to the wall using two

5x45mm screws.

16.Hook the hood onto the bottom bracket.

17.Fix the hood into its final position on the wall using one

5x45mm screw (ABSOLUTELY ESSENTIAL).

18. Connect a pipe (pipe and pipe clamps not provided, to

be purchased separately) for discharge of fumes to the

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, fix deflector F to the chimney support bracket

G using 4 screws, and connect the other end of the pipe

to the connection ring on deflector F (if dismantled, the

connection ring must be bayonet-fastened on the deflector

and locked in position using 1 screw).

19.Make the electrical connections.

20.Apply the chimney stacks and fasten them at the top to

the chimney support G (20b) using 2 screws (20a).

21.Slide the bottom section of the chimney down until it

completely covers the suction unit and slots into the

housing provided on top of the hood.

22.Fasten the bottom section of the chimney with 2 screws.

Refit the grease filter/s and check that the hood is operating

correctly.

Electrical connection

The electrical tension must correspond to the tension noted

on the label placed inside the cooker hood. Connect the

electrical plug, where provided, to the an easily accessible

outlet in conformity with local standards in force.

Where an electrical plug is not provided (for direct connection

to electrical network) place a standards approved bipolar

switch with an aperture distance of not less than 3mm

(accessible) from the contacts.

INSTRUCTION ON MOUNTING AND USE

Consult the designs in the front pages referenced in the text by alphabet letters. Closely follow the instructions set out in this

manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in

this manual, is declined.

Ariston HC 9 IX Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info