Bedienungsanleitung Ariston LI68DUO (Seite 6 von 16) (Englisch, Holländisch)

48076

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

First of all.

After performing all the operations

described in the previous para-

graphs, turn the water tap on com-

pletely, open the appliance door and

press ON-OFF button "A": indica-

tor light "B" comes on. Your appli-

ance is now on and awaiting instruc-

tions.

Selecting the wash

cycle.

Select the wash cycle by pressing

button "P". Each time this button is

pressed, one of the indicator lights

"M" will come on in sequence, se-

lect the wash cycle you deem most

suitable for the type of dishes to

wash (take a look at page 6, where

you will find the wash cycle table).

Close the appliance door and after

a few seconds, you will hear a short

beep: the wash cycle has begun.

Modifying a wash cycle in

progress.

But if you have chosen the wrong

cycle, not to worry! You can modify

the wash cycle in progress, if it has

only just started. Open the appli-

ance door carefully to avoid any

hot water splashes, then keep but-

ton "P" pressed for approximately

5 seconds, until you hear 3 short

beeps. Indicator light "M" will come

off and at this point, all the settings

will have been cancelled. You are

now free to re-set the correct wash

cycle.

You've left out a dish?

Well, it happens to everyone. Inter-

rupt the wash cycle by opening the

appliance door with the utmost

care, as usual, then insert the dish

you had forgotten. When you shut

the appliance door, the cycle will

start up from where you interrupted

it.

Finished?

The end of the wash cycle is indi-

cated by a double beep and the flash-

ing of the wash cycle indicator light

"M". Open the dishwasher door,

press the ON-OFF button as well,

thus cutting off the electricity sup-

ply to the appliance.

Turn off the water tap.

Wait a few minutes before unload-

ing the dishes: they are very hot! If

you wait a little while, they dry

better thanks to the steam. Empty

the lower rack first.

There's been a power

failure? Have you

opened the dishwasher

door?

The wash cycle stops and then

restarts when the electricity comes

back on or when you close the door.

Everything is under control!

You decide when it

starts.

When you have loaded the dishes,

you can choose when to start your

dishwasher before setting the wash

cycle desired.

Press button "C" to delay the start

of the wash cycle by 2, 4 or 6 hours.

Each time you press it, you will

hear a short beep and indicator light

"D" corresponding to the selected

delay will come on.

Now you can select the desired

wash cycle.

Close the appliance door and, after

you hear the beep, the countdown

to the delayed start will begin.

If, for example, you have set the

delayed start to 6 hours, the 6 hour

indicator light will flash, then the 4

hour indicator light will flash, and

finally the 2 hour indicator light. A

quick look at the indicator lights

will keep you informed of the

countdown progress at all times.

Once this time is up, indicator light

"D" will stop flashing and the wash

cycle will begin.

Have you changed your

mind?

If you change your mind and you

wish to set a different delay, just

open the appliance door, press

button "C" and repeat the selection.

If on the other hand you want to

cancel the delay set and you wish

You have loaded your dishes and you now have

to set the wash cycle. It takes just one minute

to learn how

Starting the dishwasher

Make sure the

wash cycle has

ended before

removing the

dishes!

to start the wash cycle

immediately, press the button in

sequence until indicator light "D"

comes off.

Once you close the appliance door,

the wash cycle set previously will

begin.

You want to wash on

one rack only?

Remember to use half

the amount of

detergent.

Your dishwasher also allows you to

wash half a load, to save water and

electricity. Before setting any wash

cycle whatsoever, press button "Q"

repeatedly to select whether you

want to run a half cycle on the up-

per or lower rack. Each time you

press it, you will hear a short beep

and indicator light "R" correspond-

ing to the selected rack will come

on.

Ready, steady, go!

If you have

delayed the start

of your wash

cycle, it is best if

you do not modify

anything while you

wait during the

countdown.

If you really have

to, then press

button "P" and

keep it pressed

down for

approximately 5

second You will

hear 3 short beeps

and all the settings

will be cancelled.

You can now

repeat the

programming

operations.

Do you want extra

drying?

Press button "E" before you start

the selected wash cycle.

A prolonged beep will inform you

that you have selected extra drying,

a short beep indicates it has been

disabled.

With extra drying, the wash cycle

will last longer, to provide you with

drier dishes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston LI68DUO Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info