Bedienungsanleitung Ariston LV 460 A (Seite 21 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

454514

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

If the power socket to

which the appliance is

connected is not

compatible with the

plug, replace it with a

suitable plug rather

than using adapters or

multiple plugs as these

could cause

overheating or burns.

Installation and moving

After having bought or moved your dishwasher to another home, a

correct installation ensures that your dishwasher will operate

smoothly and efficiently.

Your dishwasher has arrived

Hot water connection.

Your dishwasher can be supplied

with hot water from the mains

supply (if you have a central

heating system with radiators) at

a temperature of no more than

60°C.

In this case, the wash cycle time

will be about 15 minutes shorter

and the wash will be slightly less

effective.

The connection must be made to

hot water supply following the

same procedures as those indicated

for the cold water connection.

Anti-flooding protection

Your dishwasher (model LV 460A)

is provided with a special system

which blocks the water supply in

the event of leaks inside the appli-

ance. It is further equipped with a

water inlet hose (WATER STOP)

that can withstand extremely high

pressures and that turns bright red

in the event of breakage. Safety in

the event of flooding is ensured by

the second clear hose that contains

the former and thus highlights the

latter when it has turned bright red.

It is vital that you check it on a

regular basis: if you see it has turned

bright red, then you know you have

to replace it as soon as possible.

Call for an authorised technical

engineer to come and replace it.

Drain hose connection.

Fit the drain pipe into a drain line

with a minimum diameter of 4 cm

or place it over the sink. Avoid

restricting or bending it. Use the

special plastic elbow provided (see

figure) to position it in the best

possible way. The part of the pipe

marked with the letter A should be

between 40 and 100 cm above the

ground.

The pipe should not be immersed

in water.

Choose where you want to install

your dishwasher, you can even

place it so that its sides or back

panel are side by side with furniture

or up against the wall. The

dishwasher is provided with water

supply and drain hoses, which can

be directed towards the left or right

to facilitate appropriate

installation.

Levelling.

Once the appliance is positioned,

adjust the feet by screwing them

in or out depending on how high

you want it and to level it so that it

is horizontal. Make sure that it is

not inclined more than 2 degrees.

If the appliance is level, it will he

lp ensure its correct operation.

Adjusting the Back Feet

Insert the appliance into the cutout

and then adjust the height using

the screws located on the front

bottom part of the machine. Use a

screwdriver to turn the screws in

the clockwise or anti-clockwise

direction to increase or decrease

the height respectively.

Cold water connection.

Connect the cold water supply

hose to a threaded 3/4 (gas)

connector, inserting the small filter

supplied with the dishwasher and

making sure that it is fastened

tightly in place (see figure 2).

The LV460 A model, have a "Water

Stop" water supply pipe, with filter

in the threaded inlet

If the water pipes are new or have

not been used for an extended

period of time, let the water run to

make sure that the water is clear

and free of impurities. If this

precaution is not taken, there is a

risk that the water inlet can get

blocked and damage the appliance.

Antinoise protection

(where present)

- On top of the dishwasher you will

find two self-adhesive sponges.

- Glue the small sponge onto the

top cross-rod as shown in

photograph 1.

- Tilt the appliance and glue the

large sponge as shown in

photograph 2.

Both sponges must be applied

ensuring that they stick properly

to the plate.

Electrical connection.

First of all, check that the mains

voltage and frequency values

correspond to those stated on the

rating plate located on the stainless

steel inner door of the appliance

and that the electrical system to

which the dishwasher is connected

is sized for the maximum current

indicated on said rating plate.

Earth: indispensable

safety.

Only now can you plug the

appliance into a socket provided

with an efficient earth connection

(the system's earthing is a

guarantee of safety provided for

by law, make sure your system has

it).

The plug

The dishwasher plug must be

accessible even when the appliance

is installed as a built-in unit so that

maintenance can be done safely.

Power supply wire.

Check the power supply wire on a

regular basis; if it is damaged, we

recommend you have it replaced

by an authorised technical

Assistance service centre.

Condensation-proof tape.

On some models, a transparent

condensation-proof adhesive tape

has been provided.

It should be stuck onto the lower

side of your wooden worktop to

protect it from the formation of

condensation.

When not provided, this tape can

be requested as a spare part from

authorised retailers.

The special plastic

elbow should be

fastened firmly onto

the wall to prevent the

drain hose from

moving and allowing

water to spill outside

the drain.

Fig.2

Ariston LV 460 A Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info