Bedienungsanleitung Ariston PF 640 E (Seite 14 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

455053

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

555

475

Fastening Clamps - Assembly Diagram

Clamp Position for Clamp Position for

H=20mm top H=30mm top

Front

Clamp Position for

H=40mm top Back

N.B: Use the clamps contained in the "accessory kit."

f) In the event the cooktop is not installed above a built-in

oven, a wood panel must be inserted as insulation. This

panel must be placed at least 20 mm from the bottom of

the cooktop itself.

Important: When installing the cooktop above a built-in oven,

the oven should be placed on two wooden strips; in the case

of a joining cabinet surface, remember to leave a space of at

least 45 x 560 mm at the back.

560 mm.

45 mm.

When installing the cooktop above a built-in oven without

forced ventilation, ensure that there are air inlets and outlets

for ventilating the interior of the cabinet adequately.

Gas Connection for Cooktop

The cooktop should be connected to the gas supply by an

authorized installer. During installation of this product it is

essential to fit an approved gas tap to isolate the supply from

the appliance for the convenience of any subsequent removal

or servicing. Connection of the appliance to the gas mains

or liquid gas tanks must be carried out according to the safety

standards currently in force, and only after it is ascertained

that it is suitable for the type of gas to be used. If not, follow

the instructions indicated in the section entitled, “Adapting

the Cooktop for Different Types of Gas”. If the cooktop is to

be connected to tanks containing liquid gas, use pressure

regulators that comply with current safety standards.

Important: To insure that the appliance operates safety, the

gas is regulated correctly and your appliance lasts over time,

make sure that gas pressure levels comply with the

indications given in Table 1, “Nozzle and Burner

Specifications”.

Gas Connection to Non-flexible Pipe

(copper or steel)

Connection to the gas source must be done in such a way

as to not create any stress points at any part of the appliance.

The appliance is fitted with an adjustable, "L" shaped

connector and a gasket for the attachment to the gas supply.

Should this connector have to be turned, the gasket must be

replaced (supplied with the appliance).

The gas feed connector to the appliance is a threaded, male

1/2" connector for round gas pipe.

Gas Connection to Flexible Steel Pipe

The gas feed connector to the appliance is a threaded, male

1/2" connector for round gas pipe. Only use pipes, tubes

and gaskets that comply with current safety codes. The

maximum length of the flexible pipes must not exceed 2000

mm. Once the connection has been made, ensure that the

flexible metal tube does not touch any moving parts and is

not crushed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston PF 640 E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info