Bedienungsanleitung Ariston PH 960 MST GH (Seite 19 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

455091

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

• That the plug or switch are easily accessible.

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked “E”

or or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or

coloured Red.

Connect the Blue wire to the terminal marked “N” or

coloured Black.

Adapting the Cooktop for Different Types of Gas

To adapt the cooktop to a different type of gas than that

for which it was designed, (see the sticker under the hob

or on the packaging), the burner nozzles must be changed,

as follows:

• Remove the pan supports and slide the burners out of

the cooktop.

• Unscrew the nozzles using a 7mm socket wrench and

replace them with those for the new type of gas. (See

table 1, “Burner and Nozzle Specifications”).

• Reassemble the parts following the instructions in

reverse order.

• On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker

is available from our Service Centres.

If the gas pressure is different than that prescribed, a

pressure regulator must be installed at the source, in

compliance with national standards governing the use of

piped gas regulators.

Regulation of Air Supply to the Burner

The burners do not need any primary air regulator.

Minimum Regulation

Minimum regulation:

• Turn the gas valve to minimum.

• Remove the knob and turn the regulator screw

(positioned either on the side of the top or inside the

shaft - Figs. A and B) clockwise until the flame becomes

small but regular.

N.B.: In the case of liquid gas, the regulation screw must

be fully screwed in (clockwise).

• Make sure that, when the knob is turned rapidly high

to low, the flame does not go out.

• In the event of a malfunction on appliances with the

security device (thermocouple) when the gas supply

is set at minimum, increase the minimum supply levels

using the regulator screw in Fig. A - B.

Once the adjustment has been made, apply sealing wax,

or a suitable substitute, to the old seals on the by-pass.

Table1 (For Hungary) G 20 G 25.1 G 30

Burner

Thermal power

Nozzle

1/100 (mm)

Thermal power

Nozzle

1/100 (mm)

Thermal power

Nozzle

1/100 (mm)

Reduced Fast (RR) 2,45 110 1,90 110 2,30 80

Semi Fast (Medium) (S) 1,60 96 1,25 96 1,50 64

Auxiliary (Small) (A) 0,90 71 0,65 71 0,90 50

Triple Crown (TC) 3,15 133 2,45 133 2,90 91

Semi-FishBurner (SP) 1,50 88 1,15 88 1,40 60

Supply pressures 25 mbar 25 mbar 30 mbar

At 15°C and 1013 mbar-dry gas

P.C.I. G20 35,9 MJ/M

P.C.I. G30 122,8 MJ/M

P.C.I. G25.1 30,9 MJ/M

Burners and Nozzle Specifications

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston PH 960 MST GH Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info