719590

Ariston Pro 1 Eco Seite 14

14
Zoom out
Zoom in
Vorherige Seite
1/18
Nächste Seite
The Max function is deactivated even if there is a stall error, if the “OFF” status is engaged or if the +/– buttons are
pressed to change the set-point.
Setting the set-point
By pressing the PLUS or MINUS buttons, the user can choose the set-point temperature (indicated by the temperature
LEDs, with the other LEDs o ). Each press of the button increases or decreases the set temperature by 10 degrees. After
5 seconds without any action, the set-point will be conrmed and memorised.
STALL STATUS
There are two possible stall statuses:
- TOUCH CONTROL STALL STATUS
If a touch control error is detected, the status of the touch LED is undetermined and cannot be controlled. This status
is indicated by the ashing of the temperature LEDs (fast if the product is on, slow if it is o ).
- OTHER STALL STATUS
If other errors are detected, all the LEDs will start ashing.
To reset a non-volatile error, if possible, it is necessary to press the ON/OFF button (Fig. 3) to switch the product on
and o. To verify which error occurred, it is necessary to enter the diagnostics state by simultaneously pressing the
ON_OFF and MAX BUTTONS for 3 seconds. After 25 seconds, the system will return to the stall status. Note: for the
Chinese market (set through NFC), the product is reset by simultaneously pressing the ON/OFF and ECO buttons for
5 seconds.
USEFUL INFORMATION (for the user)
Before any operation of cleaning the device make sure to turn o the product by bringing the external switch to the
OFF position. Do not use insecticides, solvents or aggressive detergents that may damage the painted parts or plastic
material.
If the water delivery is cold, have the following checked:
- that the device is connected to the power supply and the external switch is in the ON position.
- that at least led 40°C (1 g. 3) is turned on.
If there is presence of steam output from the taps:
Remove power from the electrical appliance and contact technical support.
If the hot water delivery is insucient, have the following checked:
- the pressure of the water mains;
- eventual obstruction of the inlet and outlet pipes (deformation or sediment).
IF THE PROBLEM PERSISTS,NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE
BY A QUALIFIED TECHNICIAN.
The indicated data and specications are not binding; the manufacturer reserves the right to modify them at his
own discretion notication or replacement.
This product conforms to Directive WEEE 2012/19/EU.
The symbol of the crossed waste paper basket on the appliance and its packaging indicates that the prod
-
uct must be scrapped separately from other waste at the end of its service life. The user must therefore
hand the equipment over to a sorted waste disposal facility for electro-technical and electronic equipment
at the end of its service life.
Alternatively, he may return the equipment to the retailer at the time of purchase of a new equivalent type of appliance.
Electronic equipment of size less than 25 cm can be handed over to any electronics equipment retailer whose sales area
is at least 400 m2 for disposal free of charge and without any obligation to purchase new product.
EN
18
Setting the set-point
By pressing the PLUS or MINUS buttons, the user can choose the set-point temperature (indicated by the temperature
LEDs, with the other LEDs o). Each press of the button increases or decreases the set temperature by 10 degrees. After
5 seconds without any action, the set-point will be conrmed and memorised.
STALL STATUS
There are two possible stall statuses:
- TOUCH CONTROL STALL STATUS
If a touch control error is detected, the status of the touch LED is undetermined and cannot be controlled.
This status is indicated by the ashing of the temperature LEDs (fast if the product is on, slow if it is o).
- OTHER STALL STATUS
If other errors are detected, all the LEDs will start ashing.
To reset a non-volatile error, if possible, it is necessary to press the ON/OFF button (Fig. 3) to switch the product on
and o. To verify which error occurred, it is necessary to enter the diagnostics state by simultaneously pressing the
ON_OFF and MAX BUTTONS for 3 seconds. After 25 seconds, the system will return to the stall status. Note: for the
Chinese market (set through NFC), the product is reset by simultaneously pressing the ON/OFF and ECO buttons for
5 seconds.
USEFUL INFORMATION (for the user)
Before any operation of cleaning the device make sure to turn o the product by bringing the external switch to the
OFF position. Do not use insecticides, solvents or aggressive detergents that may damage the painted parts or plastic
material.
If the water delivery is cold, have the following checked:
- that the device is connected to the power supply and the external switch is in the ON position.
- that at least led 40°C
(1 g. 3)
is turned on.
If there is presence of steam output from the taps:
Remove power from the electrical appliance and contact technical support.
If the hot water delivery is insucient, have the following checked:
- the pressure of the water mains;
- eventual obstruction of the inlet and outlet pipes (deformation or sediment).
Water trickling from the pressure safety device
During the heating phase, some water may trickle from the tap. This is normal. To prevent the water trickling, a suitable
expansion vessel must be installed on the ow system. If the trickling continues even after the heating phase, have the
following checked:
- device calibration;
- the pressure of the water mains.
Caution: Never obstruct the appliance outlet!
IF THE PROBLEM PERSISTS,NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE
BY A QUALIFIED TECHNICIAN.
The indicated data and specications are not binding; the manufacturer reserves the right to modify them at his
own discretion notication or replacement.
This product conforms to Directive WEEE 2012/19/EU.
The symbol of the crossed waste paper basket on the appliance and its packaging indicates that the product must be
scrapped separately from other waste at the end of its service life. The user must therefore hand the equipment over to a
sorted waste disposal facility for electro-technical and electronic equipment at the end of its service life.
Alternatively, he may return the equipment to the retailer at the time of purchase of a new equivalent type of appliance.
Electronic equipment of size less than 25 cm can be handed over to any electronics equipment retailer whose sales area is at least 400
m
2
for disposal free of charge and without any obligation to purchase new product.
… 14 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

ariston-pro-1-eco

Suche zurücksetzen

  • Ich habe einen neuen wasserboiler Ariston Pro 1 Eco 50 installiert. Wasser eingelassen, Boiler eingeschaltet. Das Wasser bleibt kalt. Auch nach ca. 2 Stunden. Was habe ich falsch gemacht? Wie kann ich sehen, dass er richtig eingeschaltet ist? Ein/Aus-Led leuchtet. Die Warmwasser Leds (Temperatur) blinken. Wie lange kann es dauern, bis Warmwasser kommt? Eingereicht am 23-5-2021 21:26

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ariston Pro 1 Eco wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Ariston Pro 1 Eco

Ariston Pro 1 Eco Bedienungsanleitung - Holländisch - 16 seiten

Ariston Pro 1 Eco Bedienungsanleitung - Französisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info